hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi,
I just finished to setup everything to start using nRF Connect for VSCode Extension. I followed the "nRF Connect SDK Fundamentals" course in the DevAcademy.
I installed...
Hi,
nRF5 SDK for Thread and Zigbee supports DFU OTA over Thread, but I can't find the corresponding function in NCS.
If I want to implement DFU OTA over Thread in NCS...
Hi Team,
I'm analyzing to use nPM1300 PMIC in one of my projects. I planned to use the integrated Buck to power my on-board device. But, the calculated current consumption...
Hi Nordic team, I am facing an issue about using simple gpio to control external FEM( custom FEM model ) in NCS 2.7.0 & nrf5340. Here is background: 1. Our project is using...
On NRF52840, programming provision.hex with the command as follow:
%nrfjprog -f nrf52 --sectorerase --program provision.hex --reset --verify
On NRF54l15, the nrfutil...
Test platform: nRF54L15-DK
NRF Connect 2.9.0
When calling spi_write_dt, under the hood spi_nrfx_spim.c > configure is called to prepare the SPIM interface for a transmission...
I have an application that runs well on nRF52DK. It is like peripheral uart. I only use Tx/Rx and one LED. With OTA. All works as intended. I use NVS for parameters but nothing...
I've been trying to enable the watchdog as early as possible during boot. I haven't been able to find any way to configure the nrf52832 watchdog to enable itself prior to...
NCS 2.7.0 with NCS Toolchain 2.7.0 and latest NCS SDK extension
When I right click on a build configuration, there is an menu item "Copy Build Command"
which produced...
Hello, Nordic team.
We are getting the following error and log when we try to program our new nRF52840 DK on Windows 10:
Failed "reading readback protection status...
Hi! I’m trying to generate an EdDSA key pair and store it in persistent storage. I then delete the keys and regenerate them. However, after a few successful iterations, my...
I am using the board nRF5340 Soc , which by default exports two VCOM ports via the J-Link OB debugger . Currently:
VCOM1 (UART0) is used for both logging and serial communication...
Hi, although there are many guides and stories about attaching the nordic to external storage NVM, there aren't infos about doing the same with RAM.
I even found some threads...
In NCS v2.9.0 I want to use BLE security (BT_SMP, BT_SECURITY_L4) simultaneously for a peripheral and a central connection. I have tested both separately and they work individually...
