hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
I'm using the NRF5340. When I open a standard example project located in the directory: nrf\samples\bluetooth\peripheral_uart (the well-known Bluetooth data transparent transmission...
I am experiencing system resets caused by the WDT (Watchdog Timer) while using the nrf52832。
This is my WDT configuration code：
void system_wdt_init(void) { uint32_t err_code...
my sdkconfig.h related to fds
my entire code error: my entire sdkconfig
i have tried changing no of pages , using nvmc driver, but i am getting the same error steps...
HI，
I am using the nRF54L15 with SDK v3.0.0. I am currently using Timer20 for a counting function. My original power consumption was 4.6 μA when Timer20 was not enabled...
Dear Nordic DevZone,
I have a question which is quite noobish but I want to make sure I am using the right tools for the job. My setup looks like this I have a raspberry...
After gradually increasing up to ncs 3.1.0, the following issue occured: After:
LOG_INF ( "Initializing modem library" );
err = nrf_modem_lib_init ();
if ( err ) ...
Hi,
I’m working on the T5838 Invensense PDM driver for the nRF54L15 .
I’m referencing this driver: IRNAS T5838 Driver , and have updated it to work for SDK 3.0.2 (including...
Hi [Nordic Support Team / Developer Team],
I would like to confirm why the nRF54L15DK is not listed among the supported development kits for the Bluetooth: Peripheral ANCS...
I tried two different applications in BT fundamentals, the solution to Lesson 3, Exercise 1 and the solution to Lesson 4, Exercise 1. Both show "Advertising successfully started...
I'm using zephyr with a custom board (nrf52840) which has a ssd1306 OLED. I have it configured to use i2c0 and is working fine with lvgl.
When I try to enable uart0 (using...
After a recent update, I'm frequently finding the VS Code UI unresponsive due to intelliscan re-indexing.
About my setup. I have a complex environment with 4 different...
Hi Everyone,
I have designed the NRF52832 PCB, Before I order the PCB I hope you guys can review it one time.
Can you please review it, Also I want to tune the antenna...
Does the RISC-V processor of this SoC have access to all the peripherals similar to Cortex-M processor? Can it be used for edge AI using Neuton or ML studio ?
Hi everyone, I have made a custom app by merging together code from nrf5340_audio and iso_acceptor code. I have one issue however - audio_sync_timer_capture seems to return...
Hello, I have discovered that Zephyr's fuzzing sample: https://docs.zephyrproject.org/latest/samples/subsys/debug/fuzz/README.html is not working with NCS v3.0.2. Reproduction...
