Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hi,
I've made a customized version of the nrf_desktop desktop mouse build and I ported it to work on a custom nRF52833 board. I've been using Segger Embedded Studio to debug...
Hi,
I am following example to connect using TLS. I am not polling, as in the example. Should I expect that after
mqtt_connect, to be called in the callback?
mqtt_connect...
I am encountering an MPSL ASSERT: 106, 501 error followed by a HARD FAULT while running my distance measurement example on an nRF52840 using the nRF Connect SDK v2.5.1. The...
in Bluetooth Low Energy Fundamentals -> lesson 3-> Exercise 2 I opened the solution, I built the config for nrf52840 dev kit. Problem: 2M PHY is not achieved. Update to 2M...
Hi I am a student exploring on the usage of nRF52840 utilsing Thread communication protocol but i cant seems to get it setup for the configuration. The documentation is quite...
Hi,
I've been using the nRF5 SDK (17.1.0) USB Mass storage code for a data logger I have made. I am using a memory chip larger than 16KB and that code has bugs when you...
Hello,
I am currently using the nrf52840 evaluation board in developing a prototype. Once this goes into production, what are my options for programming the firmware? What...
When using l2cap to stream data at a high rate from device to an app we are seeing a hard fault in l2cap_data_pull when there is queued l2cap send data.
When the fault...
Hi,
I encountered a stop scanning issue when running the nrf5340_audio application without any configuration changes .
The only modification I made was changing the log...
I am building a firmware based on nRF Desktop, but can reproduce the issue in nRF Desktop SDK 2.9.0. The issue is that MCUBoot takes almost 1s to start the app, even with...
I'm using the visual studio code extension and things work well. I am now trying to test a more complex project found here but when pressing build I get some very long errors...
I am currently working on a distance measurement library using the nRF52840 DK and nRF52840 dongle. I have successfully obtained distance values on the serial terminal, but...
Evaluating direct access I2C operation with the NRF9160DK. I have a INA219 connected to pin 30 & pin 31. I am aware that there is a zephyr driver for the INA219, but I want...
Hello all,
Going through the nRF Connect SDK Intermediate course with my nRF54L15 DK, I stumbled upon a problem at step 6 of exercise 3 - Interfacing with ADC using nrfx...
NCS 2.6.0, sysbuild with mcuboot
nrf52840
I'm trying to add LED indication during mcuboot image transfer. Currently it takes 20-30 seconds for the image copy and the...
