Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
Hi all,
I've been wanting to start this project for awhile now, but I am having trouble figuring out where to start. I want to be able to make an iphone application which...
I try to optmize my code so it can run on the 128k chip.
My issue is with pstorage: I have 7 variables (from 4 bytes to 20 bytes) that I store in individual blocks. But it...
I have the nRF51 Dongle and an nRF51822 BLuetooth Smart Beacon kit. For software tools I have IAR's EWARM 6.7 for a complete IDE or command line GCC/GDB.
Are there any...
Hello,
my idea is to turn on a GPIO-Pin of the NRF51822-Beacon-Kit when my smartphone found the beacon. Of course if the smartphone is out of range or far away the pin...
Hi all,
I am trying to figure out how to change the LEDs blink rate on the go.
I have set up the timers_init() and let say every 500ms sensor data is read on dev kit...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
Hi,
I'm trying to get the actual connection interval used between my nRF51822 device and iOS device.
I have read this article , but I cannot get it worked.
I used sd_ble_gap_ppcp_get...
Hi,
I want to disable the softdevice (S110) in order to use the "flash_page_erase" and "flash_word_write" functions. But, when the sd_softdevice_disable() is called I get...
Hidden in the guts of this answer is:
Please be noted that not all central
stack have full support to
automatically discovery secondary
services (e.g S120 stack)...
In the code for the bootloader in dfu_dual_bank.c and the function dfu_init , I currently get an error code on timer start: 4 ( NRF_ERROR_NO_MEM ).
err_code = app_timer_start...
The device name is set in the usual way at the start of gap_params_init():
BLE_GAP_CONN_SEC_MODE_SET_OPEN(&sec_mode);
err_code = sd_ble_gap_device_name_set(&sec_mode,...
Hello,
I am new to BLE profile development. I searched in web but could not find out a useful guide for this in terms of actual implementation(coding). It is seen that all...
Why is the "old" EK "not recommended for new designs"? Will the old EK work with the IOT SDK?
(Maybe it is chip rev dependent? I don't have the my EK on hand so I don't...
Hello,
I have purchased a Intel Galileo Gen2 (x86 Arduino) and RedBear BLE shield v2.0. The Arduino IDE I use is Intel's version. I have imported the corresponding libraries...
The application uses bsp_button_is_pressed() but this device has no buttons. This results in err_code set to NRF_ERROR_INVALID_PARAM and subsequently a system reset during...
