HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
I have BOARD_ROOT set in both zephyr/module.yml and in CMakeLists, and in my boards folder I have a custom board "boards/nordic/myboard". I have all the necessary files for...
Hi,
We have come across AT%XRFTEST command problem for TX test on nRF9151 EVK. We have used nRF9151 modem firmware version 2.0.2 and executed following AT command on nRF9151...
Hi Nordic team,
I’m building an LE Audio gateway on the nRF5340 DK using the TMAP_Central sample (NCS v3.0.2, with minor local changes). The setup captures audio, encodes...
I'm working with nRF52840 microcontroller, nRF SDK 17.1.0 and Softdevice S140 version 7.2.0
The peripheral devices sends 29 bytes of data with a BLE notification from a...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
I'm currently using firmware advertising/scanning with 1M PHY, but I'd like to use Coded PHY instead. I tried changing the advertising parameters as shown below, based on...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
Hi,
I have LIS2DW12 (Gravity board) connected to my NRF54L15-DK with the following overlay:
& pinctrl {
/* Pin control for I2C21 */
i2c21_default: i2c21_default...
Hello,
I have set up the light and light_switch BT Mesh examples on my nRF52840DKs. I have used the nRF Mesh app to provision them successfully and I can see that they work...
Hi,
I am using NRF Connect environment and would like to enable by program to use MCU Boot functionality with dual-imaging support and FOTA updates.
My Kconfig.sysbuild...
I need to change the path of ncs. after try sometimes, I failed. So, I need remove all the settings and retart my work from initial status. I uninstall vs code. and install...
Dear Nordic Team,
I am trying to configure logging through J-LINK RTT for my firmware.
My prj.conf contains the following:
CONFIG_PRINTK = y
CONFIG_CONSOLE ...
My current product uses the NRF523840 with CODED_PHY periodic adverts. I want to improve the range.
I'm considering a +14dBm (SAR limited) product variant with the NRF54L10...
The nPM2100 datasheet (v1.0) states in multiple areas that the VOUT pin is discharged when the device enters Hibernate mode (and certain other modes).
Is this discharge...
Hi
It seems that the default minium DTLS handshake timeout is about 1 second. That means, there is a retransmission if a response isn't received within this timeout. In...
