Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
On the nRF52840 using ncs/zephyr v2.6.1, how can I explicitly configure the Coded PHY scheme (selecting either S=2 or S=8) for BLE Extended Advertising? Please provide the...
I tried to fully replicate the example from DevAcademy ( academy.nordicsemi.com/.../) for my project, and added a button and an LED in the overlay. However, once SB_CONFIG_BOOTLOADER_MCUBOOT...
Hello,
We need to interface the nRF54L15 with a 3-wires SPI slave (which uses one single bidirectional pin for MOSI and MISO).
I see two options here:
1. Connect the...
Issue
On the nrf54lm20 using DTLS with MbedTLS, MbedTLS's heap can be exhausted. This will result in a TLS handshake error. When this issue happens MbedTLS does not catch...
Hey,
I have a question regarding the watchdog in a low power application with dynamic sleep times of e.g. 1mim/10mim/1h. In the docs of nrf9160 and also nrf9151 it says...
Hey Nordic support, We want to perform EMC tests on the DECT NR+ for our product and need a continuous wave or tx tone sample for testing. I found the DECT NR+ shell sample...
I mean like when ever i click pristine build in the vs code i am getting this below error " Unable to build: SDK not found. Ensure that a valid SDK is used for the build configuration...
Hi,
We are using the NRF9151 with AT commands to replace our SIMCOM modems.
We would like to write the SIM profile data to the modem via AT commands just like SIMCOM...
Trying to config TDM SCK for: Master, 4 channels, 24 or 32 bits, 16 KHz...doing the math yields 1.536 or 2.048 MHz for SCK. I have 24 MHz or 32 MHz available as possible clock...
Hello, I have a question regarding external flash erase via `nrfutil` command line tool. Does the `nrfutil device` command support doing a qspi erase with custom qspi commands...
Hello,
There is a minor issue identifying a sysbuild configuration if the initial generate and build fails.
Steps to repro:
- add a kconfig that doesn't exist in...
In the past, I've been told I can bypass a lot of the Zephyr nonsense and use the HAL layers of the nRF Connect SDK directly. So if I want to use what was called nrfx_twim_xfer...
Hello,
I noticed the Audio application explicitly states that WAV sample rates other than 48kHz is not supported.
Is there any risk to modifying the code to support other...
