I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
To preface:
Board: nRF9151DK
nRF Connect SDK / Toolchain: 3.1.0
Hello,
I believe I found a bug regarding PSM (Power Save Mode). Specifically, you can't disable...
Starting with the lbs example from lesson l4e2 of BT fundamentals course, I'd like to send an indication similar to the button (and keep the button). I basically created duplicates...
I am using the nRF9151-DK with the standard (from code examples) firmware . When configuring both P0.13 and P0.17 as ADC inputs, I notice that the current consumption on P0...
I am working with the connected_cs examples on the nRF54L15 DK and trying to swap the GAP roles. In my case:
Initiator = GAP Peripheral
Reflector = GAP Central...
I am working on a Bluetooth Low Energy (BLE) project using the nRF52840 Development Kit (DK) , which has been reconfigured to simulate an nRF52805 chip. The firmware is based...
How can you get the simple channel sounding test going with the bluetooth/cs shell commands?
I've got the shell working over UART and devices talking with each other but...
I tried to add external memory to mcuboot. In fact, I have successfully added it in app, but the same configuration seems to have problems in mcuboot ，mcuboot reports an error...
Hi,
We are developing a hardware and software solution for a locator tag using a minimalist approach. We want to use both, the Google Find Hub and Apple Find My Network...
I maintain an nRF52840 project on the legacy nRF5 SDK and am migrating to an nRF54L15 Bare Metal project.
I could not find a bare-metal “radio test” example, so I’m bootstrapping...
I do connect 52840 DK board to PC through USB cable, sine I want to see runtime log. but meanwhile, I want to use PPK2 to see the current of 52840 DK board, Can I get the...
Hi everyone, I noticed something unusual while testing BLE transmission and reception:
Transmitter: nRF5340DK
Receiver setups tested:
config：Target board...
Hi,
If I build the extxip_smp_svr sample app for the nrf5340dk board. The network image firmware version is set to 0.0.0.0.
To reproduce the issue, do the following...
In Lesson-3 Ex-2 for the BLE Fundamentals course, the steps for setting preferred PHY (steps 7 thru 9) is causing fault on my nRF52840-DK board.
Log messages are as follows...
Hi Nordic Team,
I'm currently working on integrating TagoIO using MQTT in our application. While attempting to add the MQTT connection details—specifically the username...
Hello,
I have a problem with a custom board using a nRF9151.
I can flash the nRF9151 and it seams to flash successfully (I tried with a blinky program and the leds start...
