Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hello there!
I'm quite new to the topic and just tried to dig into it a bit, so I'm sorry if I didn't get all things yet about the nRF5280 Dongle :) .
Right now, I'm following...
Hi all,
Using the thread CLI example (on a PCA10056 board) as a starting point I would like nodes to connect automatically to a thread mesh when booting. I then want to...
I use the following example source code to test NFC pairing.
Example source code for NFC: nRF5_SDK_17.0.2_d674dde\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\experimental...
Hi
thank you very much for your paying attention.
Yes the peripherial_uart sample seems to be a good choice for my project. But Uart 0 pins didn't come out on GPIO connector...
Hi,
We are trying to create a network using 20 movesense sensors and BWG840 Fanstel gateway acting as the central. The gateway is running a modified ble app uart multilink...
I'm a beginner in BLE applications, and I'm having trouble with connecting nRF toolbox application
I wanted to use UART function provided in nRF toolbox.
But, an e rror...
Hi,
I wish to run an existing project in Segger embedded studio for its debug capabilities (Currently the project runs in VS code).
I'm using the nrf52832, running a bare...
I'm trying to add the unity test integration to our project, but failing to build, since the project has a dependency on nrf_oberon
For the sake of completeness, the project...
I'm having trouble connecting Thingy:91 to cloud.
I've installed both the modem and HEX image in the board successfully.
I've added the SIM card successfully to the...
I've had intermittent issues with the nrf9160 modem using mfw 1.3.0 with an iBASIS SIM getting stuck in "searching" state when first powering on. The symptoms are similar...
I am using a nrf_drv_twi_tx() and nrf_drv_twi_rx() for a simple I2C transaction but I'm noticing a strange behavior.
If I don't use APP_ERROR_CHECK(err_code); right after...
Hi,
We are developing a flutter mobile app, for Actility/Abeeway (chips from Avnet Silica) using flutter pluggin that relies on the Android SDK. In some situations (after...
Hello,
I am using NCS v1.6.0, nRF Connect for Desktop v3.7.0, and the Bluetooth Low Energy app v2.5.1 (part of nRF Connect for Desktop). I am using the nRF52840 Dongle with...
Hello! I am using nRF52840 develop product. When nRF52840 circuit board has been moved away from the cell phone and is out of the BLE range, I want to send message via UART...
