Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hello DevZone,
I have a confusing question about TF-M. Need help from a TF-M expert.
In this document , it says that we must disable uart1 in non-secure application, because...
I'm trying to test the overall pwoer consumption of my setup (nPM1034EK and nRF54l15DK) using the PPK2. As I've started this, I've gotten far higher numbers that I expected...
After I reset the kit (custom equivalent to nRF52DK) it advertises, and I can connect from the BLE Standalone App on my Windows computer. But it only advertises for a short...
I recently bought a fanstel blg840 device, and I have programmed At client firmware in nrf91 and custom code into nrf52, but the problem is nrf52 is sending at comments to...
I am trying to work with my flash deivce in my code. for some reason:
const static struct device * int_flash_dev = DEVICE_DT_GET ( DT_CHOSEN (zephyr_flash)); doesnt work...
I have been having a series of issues with programming from nRF Connect using a J-Link programmer. I have made a couple of other recent posts and in each of those, I thought...
hi,all
I used to use nrf54l15dk board as a client server, want to connect to a bluetooth remote,and get bluetooth remote notify message;
I use sample "central_hids...
Hi guys,
I have MQTT v5 up and running but I am currently trying to implement one-way TLS then mutual TLS once it's completed. I am not too sure what I am doing wrong but...
Hi:
My environment is: Windows laptop, nRF52 DK (Peripheral), nRF52840 Dongle, Mobile Central (iOS and Android), and Wireshark nRF Sniffer for Bluetooth.
Peripheral sends...
Hello all,
I have problem with flashing the code. It gives me memory protection error.
Steps I followed for creating firmware and flashing:
1- I took a sample from nrf...
I'm working on a product prototype using the nrf5340 audio dk to send audio via Auracast. We started from the nrf5340_audio application, as it implements a large fraction...
While testing UART communication between a Seeed XIAO board and the nRF9151 DK, I connected the following pins: - XIAO 3.3 V → DK VDD - XIAO GND → DK GND - XIAO TX → DK RX...
Hello,
In the nRF52840 datasheet, some pins are explicitly marked as “low frequency I/O only.” However, I couldn’t find any similar indication in the nRF54L10 datasheet...
Hi everyone,
I’m testing a custom nRF54L15 board with BLE, but it gets stuck inside bt_enable() . To debug the issue, I checked whether my 32 MHz external crystal (HFXO...
