Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
EDIT: We found the reason for this and it is a hardware issue. This question can be deleted as it is no longer valid.
-----
Hello,
We are currently developing a...
Hi!
When opening the LTE Link Monitor in nRFconnect 3.7 under Linux (Ubuntu 20.04) only a "whitescreen" appears after I select the device. The application is not visible...
Hello,
I am using NCS v1.5.0 and would like to check is a KMU slot is being used or not. I erased the whole SoC and tried reading the directly the registers, in secure mode...
which pins can be used as PWM output pins in nrf52811.
Can I use them directly or I need to add some hardware to use the PWM feature.
I have an NRF5811 SOM (EYSNCNZWW...
Hi Sir/Mdm, I want to use 1.54 inch e-paper module from waveshare with nRF52840 dongle with Zephyr RTOS. I have read the documentation from Zephyr about the display and noticed...
Hi,
We use the nRF52840 and have now run out of space using debug mode compilation (using CMake from bash).
When we compile in release mode, we get 50% full flash, so...
Hi,
I am using nrf52832 and mesh sdk 3.1.0 with nrf5 sdk 15.2.
We use dual bank approach for our firmware update with the normal nrf5 sdks ble bootloader. But now our...
Hi.
I have been trying to implement my own Model into the Light Switch Example (Mesh SDK 4.2, SD s140 7.0.1, Hardware: nrf52840 DK), according to this Thread:
Adding Simple...
I'm implementing the WS2812 driver on custom hardware and have some confusion around the hardware tuning parameters for the SPI implementation. The description of the device...
Hi everybody,
We ran into a Zephyr configuration issue which is related to Zigbee and Zephyr's networking stack. In our setup we would like to use Zephyr's modem library...
Hi,
I have nRF52840 DK, for nRF52 series devices. I switched from nRF52 SDK to nRFConnect SDK.
I reviewed
http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
Hello,
I am running ble_app_beacon demo from nRF5 SDK 17.0.2 on nRF52 DK and would like to decrease power consumption as much as possible. From this post , I have seen that...
