Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hi, I am using nRF Connect SDK 14.0 with nRF9160 DK.
I want to use nRF52840 as a controller and nRF9160 as host. To achieve this, I flashed hci_uart sample on nRF52840 and...
Hello!
I move my device from nRF52811 to nRF52820 ( QDAA-C00 ) and I have a problem when using a comparator and TWI
If I configure TWI0 or TWI1 and use it with external...
Good day,
I am using a DK board with the nRF52832 (pca10040) and I am using a 4 kHz buzzer connected to the gpio 16. I have seen the examples pwm_driver and pwm_library...
Hi, I am using the Nordic nRF52832, with the Segger IDE（Nordic）, and v1.4.0 of theSDK, and would like to know how to enable both LLPM and Multilink.
I am starting from the...
Hi.
I want to ask about the Queued Writes module and the NRF_SDH_BLE_VS_UUID_COUNT. In the example ble_app_uart, in the "services_init(void)" function we initialize the...
Hi,
I'm having difficulties running the secure bootloader example (ble_debug version), it doesn't seem to be advertising or providing any logs.
I'm currently using the...
Hi,
I want to create a fresh project in Keil with nRF SDK as static library included into application. I have created the project, but when I run, the code always stuck...
Hi,
The error I get is as followed:
Output/Debug/Exe/Lesson10_Part3.elf section `.nrf_balloc' will not fit in region `UNPLACED_SECTIONS'
region `UNPLACED_SECTIONS' overflowed...
This is my third and final attempt at getting a custom nRF52 board to appear on my phone as an Adafruit Feather device. I have no issue with the genuine Adafruit hardware...
Hi! We're preparing a medical device and are evaluating nRF5340 chip. We'd like to know when the chip and PDK will be production ready i.e. when Development Kit for nRF5340...
Hi,
One of my customers is applying LWM2M to their target application.
And they are trying to fix LOCAL PORT of LWM2M.
I heard that when end equipment is registered...
Hello
I use nrf52832 and mpu6050. I am trying to obtain values for pitch, roll, and yaw using mpu6050.
I don't know if it's because there's no magnetic sensor, but there...
