I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
Hello, I'm not very famililar with Airfuel, but I want to add in my device wireless charging function. I start searching solutions for this challange and I found Airfuel and...
Hi
I am facing problem with segger. Project get compiled and able to program hardware but hardware is not working until debug process is start. After put hardware in debug...
Hi,
I am trying to establish UART communication between two nRF52 Dev boards. I flashed both of them with UART peripheral example from 15.2.0 SDK and connected TX,RX and...
Hello,
Recently I'm working on the project that utilizes the nRF chip and the external memory MX25R3235F. The SDK is 14.2.
I'm trying to configure the peripheral and the...
Hi I am using nrf52832dk as master and slave for spi communication. I want to send below data over spi. 0x8000000008 0xEC000100C5 I am get confused in transfer function of...
Hey,
referring to my previous thread in https://devzone.nordicsemi.com/f/nordic-q-a/44298/running-usbd_hid_generic-in-nrf52832-using-a-custom-usb-module-mcp2200 . so am...
We are using the Development boards nRF52-DK from Nordic and trying to utilize the mergehex.exe downloaded from Nordic website.
using Segger Embedded Studio (non commercial...
Sir,
I have one nRF52840 DK and ADXL335 accelerometer. I need to get the 3-axis values, Xout, Yout & Zout, from the accelerometer and send through BLE to my nRF mobile app...
Hi,
I was going through generic_level_messages.h and generic_level_common.h files looking for the parameters for generic level status message.
I noticed that generic_level_messages...
I am using nRF51822 with SDK 10.0. I want to configure a GPIO pin which can wake up the MCU from SYSTEM OFF Mode and call its IRQ handler. Please find below configurations...
Hello,
I am using an nRF52dk with no additional hardware, in conjunction with SEGGER Embedded Studio V4.12. I started with an example from nRF5_SDK_15.3.0_59ac345 called...
Hi, I have modified the twi_scanner example of the 52840 DK to be compatible with nRFDongle.
I fully erased the dongle with Segger and passed the new hex file with SWD cable...
I used NRF connect to connect to a slave。
I want to use the central to connect to the device。
this is my code.
but the service is not found。
static void...
