Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
I have been reviewing the datasheet of the BLE audio nRF5340. It lists multiple power rails in power section.
Is any power-on sequence required for the SOC.
Also, can...
Using NCS 3.1.0 - getaddrinfo with "offloaded sockets" (nrf9160/51) and ipv6 results in struct sockaddr_in6, where some "c struct padding bytes" (the last 3 of 24 bytes) are...
I flashed the thingy91x using NRFCloud connect. Provisioned it in nrfcloud using hologram SIM cards. How do I turn on air quality and all other sensor information?
ZBOSS NCP: ZBOSS NCP Serial Protocol, Version 1.5 states that a "Full featured Zigbee PRO r22 platform is provided".
Is a more recent version of this document available...
New project using Nordic platform and I need to send multiple commands (32bit fixed size) to a device quickly using SPI with the CS toggling between each. I just want to confirm...
Hi Nordic Team,
I am currently developing a commercial product using the nRF Connect SDK (NCS) . The system consists of several nRF52 peripherals and a PC-based application...
On the nRF9151dk, the transmission line coming from the nRF9151 starts with a 0.1 mm trace width and a 0.46 mm gap, which corresponds to a 50 Ω characteristic impedance. However...
Hi,
using nrf connect SDK v3.1.1
using nrf54L15 development board.
I am trying to run a simple button event yet callback is not fired when
CONFIG_PM_DEVICE_RUNTIME...
Hi
Could you provide nPM1300 NTC pin inside structure?(pull up resistor value, pull up voltage, others..)
And I want to know how to calculated NTC temperature by measured...
Hello everyone,
We'd like to use the rom_report and ram_report commands to be able to see (with a somewhat granularity) how much ROM and RAM do specific feature use so that...
Hi,
Question on the nRF7002. Can it be used as a hotspot to support 5 -10 wifi clients?
Basically, the need may be to download user manuals on site with a tablet.
...
Description
I was following the tutorial from DevAcademy regarding the setup of the nRF Sniffer for Bluetooth LE : DevAcademy: nRF Sniffer for Bluetooth LE
However, the...
Hello,
I designed a PCB using nRF52840 for controlling the board.
I have physical access to the following pins : SWDIO, SWDCLK , VSS , VDD , nRESET.
What is the boot...
Hello,
I am trying to exchange data with an external slave sensor via SPIM communication using the nRF5340DK.
I am currently facing two main issues:
1. The spi_transceive...
