Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hello!
I am stress-testing the nRF54L15 devkit by sending it random-sized chunks of data over UART at 921600 baud, which the devkit code receives using the asynchronous...
We have a common codebase with both softdevice (nRF51/52 code) and now zephyr (nRF54 code). To make our code compatible I have the following replacement to sd_temp_get. This...
Hello Nordic team,
We're experiencing a GNSS issue with our nRF9160-DK (PCA10090 1.1.3 2024.44) and would appreciate any guidance you can provide. About 4 days ago, we were...
Hi Nordic Support Team,
I'm currently experimenting with Channel Sounding using a couple of nRF54L15 boards.
I am trying to obtain raw I and Q samples so that I may analyze...
ncs v2.6.1
If I use bt_conn_le_create() and do not use the default (0) value for create_param->timeout, the actual connection creation timeout does not match the description...
I'm trying to program a custom board with a Raytac nRF52832 module using the nRF52 DK's onboard J-Link via the P20 debug out port. The J-Link only detects the onboard nRF52832...
Hi,
I've been working through the Nordic Bluetooth ESL Tutorial and have the sample code up and running (using a nRF52833 DK as the tag and a nRF5340 DK as the access point...
We have custom hadware which we can successfully added the bootloader. We can generate .bin files & bootload them via BLE using the Nordic devicemanger app on our smart phone...
I am using NCS V3.0.2 with a custom nRF52840 board, which functions as a BLE peripheral. The application that I am working on fully depends on the BLE connection, so the crucial...
Hello. We need to add more end devices than default (10) on our Zigbee coordinator and that was solved with
zb_set_max_children( ZB_DEFAULT_MAX_CHILDREN );
where ZB_DEFAULT_MAX_CHILDREN...
Hi, I use nrfconnect SDK 3.1.1 and nRF52840 (as a dongle, DK etc) Using the power profiler kit 2 I see legacy advertising (TX/RX) peaks of about 32mA (with txpwr=8dBm, 3.2V...
Hi guys,
I'm working on this project which was basically a migration from STM32 to the nordic NRF52832 in order to enable the BLE beaconing mode.
It has been a challenge...
Dear Nordic Support,
I’m working with a Thingy:53 device and encountered a persistent issue during recovery. The device is recognized via J-Link (serial number: 1057760136...
Hi everyone, I'm trying to set up a bootloader chain using sysbuild (NSIB → MCUboot → APP) so that MCUboot can act as an upgradable bootloader. I'm working with the nRF54L15...
