Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Symptoms:
When running Bootloader + SoftDevice + App (with SoftDevice enabled in the app), The bootloader runs correctly and starts SD. The app is started, but crashes...
Hi,
I'm using nrf Connect SDK 3.1.0 and want to control three WS2812B LEDs with the LED strip driver. Therefore, I created the devicetree entry similar to the sample:
...
Hi!
We are currently building a product using nRF9161 on (rather old) nrf-sdk version v2.9.2.
After production we are testing the hardware functions of this product using...
We have a product that was built on NRF SDK 1.6.1, which is zephyr 2.6 as far as I can tell. We have ported it to zephyr SDK 3.7 (not NRF SDK) because there have been many...
I struggle with my experimental project of breath and apnea detection. It works except that I cannot reduce the poser consumption bellow 1mA when powered on battery, despite...
Hi I saw NRF Connect for Desktop is in the maintenance state, no more development. New recommendation is NRF Connect for VS Code, right? In this case, how about the PPK2 tools...
Hi,
Currently, I know that OTA updates for the nRF5340 can be performed using Device Manager and the nRF Connect mobile application. However, if using a PC, is it possible...
SoC: nRF52832 or nRF54L15 SDK: nRF Connect SDK v3.2.0
We are considering controlling coexistence via PTA signals when operating a third-party Wi-Fi device together with...
On this page https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/build/dts/howtos.html#set_devicetree_overlays and many others in this documentation, it appears that...
The subject issue is documented here as " NCSDK-20567: Partitioning limitation with MCUboot swap move": This issue has been open for while. These two DevZone tickets refer...
I use ncs3.0.2 to develop the 54l10 chip. I created a timer using k_timer, with a period of 1 second, to record the device time. Although I have adjusted the load capacitors...
I'm attempting to enable provisioning using attestation tokens in my project. As soon as I add the config;
CONFIG_NRF_PROVISIONING =y
The build starts failing with;...
Hi,
We are facing a strange behavior where the consumption we measure on the nRF5340 doesn't change according to supply voltage like it is supposed to do in DCDC mode. ...
Hello Nordic team,
I want to be able to save the log into a file and then read it in order to send it's content via HID.
I've managed to make the log back end FS work...
