Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I have written a word (32 bites) in 0xFF000 using nrf_fstorage_write(), When BLEInit(), nrf_fstorage_evt() callback not trigged,
BLE_Sleept()
nrf_storage_write()
BLE_wakeup...
Here is an example main.c which you can use as an example to understand corectly how to use the GPIOTE module and toggle the 4 LEDs numbered 1-4 in the nRF52 DK. Forget about...
Hi,
I am trying to implement external flash storage onto my custom board, featuring an nrf9160-SICA-B1 and a Winbound w25q128jv 128Mbit flash chip on SPI3 (I cannot get...
Hello,
we have a problem with modules from raytec MDBT42Q.
We have modules which work with our software as expected, and other ( newer ) that will stuck in Software. ...
I use the following :
-> nRF52840 Dongle / µC on the other side
->Blutooth Low Energy v3.0.1 (desctop version)
I try to read a characterictic after connecting and get...
During an execution of a winbond w25q64jv command (any command) during a BLE_GATTS_EVT_WRITE event the SPI bus goes inactive after the command is sent:
There is apparently...
Hello,
I tried to change the defined UUIDs for the BLE service and characteristics in the LED Button Service example (lbs.h).
E.g.
But the result is somehow...
Hello, I found that my device is more prone to disconnection due to 0x8. And I saw the log and found that most of the disconnected cases were immediately disconnected as soon...
I am using the NRF distance measurements examples between two nRF5340 boards to calculate the distance between them. I want to know how the distance is calculated in phase...
I am attempting to download v10.18.0 of the nRF command line tools for Linux x86 64. However, the .deb file provided is for arm64. Could you please fix this in the nRF command...
While trying to download the latest nrf-commanline-tools for LInux x86_64 I have noticed that the link for the DEB package is wrong: it leads to the arm arch., not the amd64...
Hi.
We've built an app for the nrf5340-based module using the nrf connect 1.6.1 SDK and its out-of-the-box Zephyr/MCU boot loader etc., code base. We build using west, which...
Hallo Team,
We are planning to use nrf5340 for one of our project which requires low energy audio and sensor data transfer. Can you please evaluate if our use case is...
