I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
I can't seem to find the right configuration item to set to disable the spinning up of the sensor_sim task, which I have no need of in my application.
I've tried setting...
Quick question I think. I'm using the NRF52 to program a PIC16 over SPI. The PIC16 switches it's line to output once it receives a particular command so as such I need to...
Hi,
I'm trying to mimic a fully functional zigbee color light bulb using the nRF52840 dongle.
Starting with the NRF5 Zigbee example light_bulb (examples/zigbee/light_control...
I apologize if this question is stupid
I want to read data in p_adv_report. I use the command NRF_LOG_INFO ("name =% x ", * p_adv_report-> data.p_data); but it's meaningless...
I am trying to use I2C (TWI) to communicate between my custom nRF52811 board with an Arduino. Currently my program hangs at the while (m_xfer_done == false); loop as m_xfer_done...
Hi Team,
We wanted to verify Sleep current numbers for nRF52833 SoC based custom development kit.
Is there any readily available firmware to verify these numbers?
...
I'm teaching a course, using the nRF52840-DK board as the lab platform.
Students download Segger Embedded Studio and compile the "Hello World" project from the 'nRF Samples...
Hi,
I have built a prototype that has two SPI slave devices connected to it and it works perfectly. I have now tried to add an SPI SD card aswell by following the FatFS...
Hi,
I'm now using nRF52833 DK to do the AoA test. I achieved the IQ sampling for a single antenna, but when I tried to switch between multiple antennas, the IQ results seems...
Hello!
My problem is that I am getting duplicates of the ACK packets I send from my PRX device to my PTX device.
To debug this problem, I configured my PTX to continuously...
Hi Devzone:
Is there a way to designate one ram block exclusively for radio use? The reason I'd like to know is the following:
Under nRF52833 AHB multilayer section, there...
I need a specific extended panid. Refer to the CLI example and add the following program:
Through the log, the extended panid returned by the device is 0000000000000000...
Hi,
I am developing an application with to 7 transmitters (peripheral) and one receiver (central = nrf52DK), all NRF52832.
I have 1 question and one problem to solved...
