Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello, I'm testing the nRF21540 FEM on a custom nRF52840-based board using the nRF Connect SDK.
I’ve enabled CONFIG_MPSL_FEM CONFIG_MPSL_FEM_NRF21540_GPIO_SPI CONFIG_BT_LL_SOFTDEVICE...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
Hello Nordic Team,
we’re evaluating nRF91 for our next product platform (being strong in LoRaWAN since years) and hoped to quickly run some first field trials with the recommended...
We have been using wget to get nrfutil on CI. Today it stopped working. Giving error " ERROR 403: Forbidden " The same link still works on browsers. The link is: https://developer...
Hi,
We're running into a high memory usage issue on an application that is using the nRF5340-nRF7002, multiple sensors on SPI, SDC with littleFs, BLE and WIFI. The WIFI...
Hi,
I'm currently working with a nrf6191 on a custom board using Zephyr and I would like to use little FS as my file system.
So far I've set the configuration and overlay...
Hi,
As the title states, after a while, the nRF7002 fails to connect SSID after a while. It happens either we perform net_if_up/down or not. I suspect the nRF7002 to be...
Hello,
I’m developing a project using the nRF52832 and I’d like to put the MCU into the lowest possible power consumption mode while still being able to wake it up via a...
Hello, checking if I'm doing this right of restoring initial fw for 91X to work with Quick Start v1.2.0. as described here in Get Started, https://www.nordicsemi.com/Products...
I have devices that manually define PDP context 0 in order to set the APN to the required value for the SIM.
Typically, once connected to the network, the IP address gets...
i would like to get MCC, MNC and other cellular data via API. I found lte_lc_conn_eval_params_get() function/API as part of <modem/lte_lc.h> that has the information I am...
i would like to get MCC, MNC and other cellular data via API. I found lte_lc_conn_eval_params_get() function/API as part of <modem/lte_lc.h> that has the information I am...
Setup NRF52840 with SDK 17.1
FreeRTOS tickless idle mode
When we call xTaskNotifyWait and then get the notification then function returns but the result of the function...
Hello!
I bought dev board with this module and plan to use it in my product.
I bought a development board with this module and plan to use it in my product.
While I...
