Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
I am trying to copy from this example:
https://github.com/NordicPlayground/nRF52-ADC-examples/tree/master/ble_app_uart__saadc_timer_driven__scan_mode
but I get:
./nrf5_SDK_Current...
Hi,
I'm trying to understand the PSM availability of my local network.
After playing a bit with the RAT and RPTAU values, I found out that using RAT=16~30 secs and RPTAU...
Documentation states that k_fifo_is_empty() returns 0 if data is available in the fifo (which is really implemented using a queue).
I'm receiving some spurious interrupts...
Hi,
In these conditions "custom device connected+bonded and whitelist enabled", when the device scan for beacons it see only the smartphone bonded to the device (don't see...
Hi! Looking at the product specifications V1.1 specifically 5.2.1 Electrical specification, one can see that on Sleep System On, full ram retention wake up on GPIOTE Port...
Hello,
I have following problem.
I use the nRF52840 DK and want to run it in nRF only mode, so I have the minimum power consumption. If I set the DK to low power mode...
Hi,
I encountered fota_evt_handler in azure_iot_hub.c is missing the call to azure_iot_hub_notify_event for the AZURE_FOTA_EVT_ERROR case, resulting in the application not...
I'm currently working with the MX25R6435F flash chip on board the nRF52840 DK and I'm running into issues with it. I don't know whether it's down to my lack of understanding...
Hello,
I am using nRF52832 integration. While drawing the PCB, I could not find the pin definitions in detail in the datasheet. Which pins correspond to SPI, I2C, and UART...
What is the main clock frequency when application is running in thingy52? Is there a way to measure it from GPIO?
BTW, want to know what is the clock source and setting...
Hello,
I'm using SDK for Thread v4.1. I built my project on top of multiprotocol example "ble_thread_dyn_template". I want to increase the radio output power of the device...
Hi,
I have a custom board with nRF52840 and I'm using nordic SDK. My image size is increasing because I have lots of peripheral connected in my board. I would like to use...
Hi, I'm about to perform an RF-PHY test on a module using nRF8001 to get a QDID. In that connection, I would like to know the specifications of the nRF8001.Can you tell me...
