Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi，all:
I use 9160DK to test PSM mode as follow steps with at_client example：
1、set ”AT+CFUN=0“ to power off mode;
2、set "AT+CPSMS=1,"","","10101010","00100001"" to...
Hello,
We're making RuuviTag sensor beacons which log environmental data to flash. Logged data is later read by a mobile phone application over Nordic UART Service.
The...
Hello
I am programming using the nrf52832 module 'MDBT42Q-512KV2' in SDK v17.0.
This works well without any problems in the example ble_app_blink. However, the BLE is...
Hello
I am contacting you to have a little more information concerning the messages which are sent in the examples thread_simple_coap_client and thread_simple_coap_server...
We have performed the DTM mode setup on the ATEX HW variant of nRF52832 chipset using nRF go studio application where the app is throwing an error as attached in the screenshot...
This is more related to the Segger Embedded Studio than Nordic parts or SDK, but I'd like to hear what kind of experience other Nordic users are having with the Segger IDE...
I want to run BME680 sensor example from zeyphyr->samples->sensors, i loaded the project with adding nrf9160dk_nrf9160ns overlay file with the contents :
&i2c2 { compatible...
Hi,
we are using the nRF52840 in a medical ECG recorder. To stream the data as fast as possible we want to use the 2Mb phy. Everything is working as expected under iOs and...
Hello,
I am using Nordic's SES 4.52 with a project from nRF Connect SDK 1.3.1. I have preprocessor definitions I'd like to add to the project to mirror those added on the...
The nRF9160 datasheet tells the reader to refer to the website for Altium files. However, the only files I can find are for the development board. Is it possible to release...
What is the best way to change advertising data for each advertising packet in Mesh SDK's each of proxy / dfu / provisioner?
Using Mesh SDK 4.1, it would be ideal to be...
I have a working code which implements a UART peripheral written originally with SDK15.0
I would like to port it to the latest SDK 17.02
I can get advertisement and I...
Hello!
I have problem updating application firmware with the following message.
In nRF Connnect v.3.6.0 Programmer has been selected.
Log file indicated. INFO...
Hi,
We are trying to develop a wearable device that needs to sync time over a BLE connection and write the time to the internal RTC. We are using the nRF52832 for development...
