Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
I am following the instructions as per Getting Started with the Asset Tracker Template.
I have successfully created the environment and done the West Update.
When I do...
Hei,
I have nRF9151 SMA DK v0.9.0 running with board controller FW v1.1.0. This is stated by the Board Configurator v1.1.2 tool.
I tried to set both nPM VOUT2 and VDD...
Hello,
For my project I am interested in performing IQ sampling in the payload of a BLE packet, using nRF52833 at both receiver and transmitter.
I am manually configuring...
Hi,
We've been developing a product using nRF52840, where it does a lot of advertising and scanning.
We've migrated from SDK v2.5.2 to v2.8.0, and recently discovered...
nRF Connect SDK v3.2.1 on Windows 11
I am trying to build the Matter Light Bulb sample using a nRF7002DK but run it over Thread instead of WiFi (the default). Since this...
Good day,
When using the bt_gatt_discover() with a NULL UUID parameter, the code sweeps all UUIDs available from the start_handle to the end_handle. This is verified with...
Development environment: MacOS Sequoia (15.4.1), Visual Studio Code v1.108 0, nrfConnect 2026.1.1242
I am trying to develop a "workspace" project with a nRF52840DK as my...
I understand that the rf path should be 50 ohm coplaner to the output matching network that should be placed very close the the NRF chip. The recommendation shown in the reference...
I’m facing a Power Profiler Kit II (PPK2) measurement discrepancy that appears to depend on the host PC , not the target board or firmware.
Target setup
Custom board...
Hi all,
What is the increase in current consumption or power consumption when measuring RSSI with the nRF52833?
My device is a peripheral. I would like to estimate this...
I am using nrfx_nvmc_page_partial_erase_init() and nrfx_nvmc_page_partial_erase_continue() to erase flash in-between wireless connection events. The datasheet states: " The...
I have an IoT project that reads data from a proprietary device via an I2c SBIffer. The device consists of a controller and a small display, which are connected via an I2C...
I am referring to the ncs\v3.1.0\nrf\samples\bluetooth\throughput\sysbuild\ipc_radio\prj.conf for the nRF5340 and extrapolating that to a central application with multiple...
Hello, I hope this question is allowed here. I have received this email, after having been active on this forum:
Hi Mads, I saw you on the Nordic forum and wanted to get...
Hi,
We've been using the PPK II for basically every IoT project we've carried out in the last few years, and it has been an incredibly useful tool.
Our standard use case...
