Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
I have setup the Segger Embedded Studio for ARM (Nordic Edition) V5.10d, and managed to compile a sample app from ,
V1.4.2 -> nrf -> samples -> bluetooth -> peripheral...
Hello,
I have different behaviour with 2 identical boards.
They behave differently (at least for BLE functions).
With jlink interface, I saved the flash binary of...
I have installed the toolchain according to nRF Connect guideline, on my MAC OSX.
My option settings are listed in the attached image.
I downloaded release 1.4.2.
...
Hi Sir
We are developing a product with nRF5340,
Now we faced the PCB layout symbol creation issue,
I can't find any information about footprint of nRF5340,
Can someone...
Hello,
I am trying to get acquire the accelerometer data every 4 hours for a sample duration of 60secs. These data are stored in RAM and on ble connection with the mobile...
Hi,
I'm totally new to programming nRF DK's.
What am I using?
Segger Embbedded Studio for ARM (Nordic Edition)
Toolchain: nRF Connect SDK v1.4.99-dev1
The "mqtt...
Hello there,
Since we use the lower level modules from Nordic's SDK for Mesh 4.2.0 - namely timeslot.c, bearer_handler.c and some additional modules to make them work properly...
Hi,
I just happened to stumble across these lines (123 to 126) in nrf_drv_uart.h:
And I noticed that on line 125 NRF_UART_ERROR_FRAMING_MASK is mapped to NRF_UARTE_ERROR_PARITY_MASK...
Hi, I've got our custom board with W25M02GVZEIG and I want to be able to read it out in a way that is fast and works with XIP. It's ok if it takes more time to write.
So...
Hi, I've made UART (BAUD RATE 1M) only on central after recieve all data (8kB). Peripheral is sending data from own ram (collected data from SPI sensors). What and how i need...
Hi,
I am trying to start from scratch BLE firmware to send and receive data from the development kit PCA10100 and nRFConnect App. I am following this course on Github here...
Hi,
i am trying to send temperature data along with timestamp as a string over BLE to a smartphone. i did the temperature reading part and now want to add timestamps to...
Can you show how can I merge the ble_app_uart and ble_app_uart_c into one code?
Once the device wakes up, it will check its GPIO - if it is '0', the peripheral will start...
Hello,
this is my second question in this forum, again regarding floats. (I hope its not something obvious like last time)
I`m getting very different results from asinf...
