Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi, I am new to BLE mesh. As I have understand , a provisioner is one which forms the mesh network and assigns addresses to the node and make them join to the network.
1...
Hi,
How do I-
1. Start a timer when sending data from nrf to host (PC) in form of input report.
2. When the application running on host machine receives this data, send...
When i try to add RSSI viewer app in nrf connect it shows error
Unable to install: Unable to download developer.nordicsemi.com/.../pc-nrfconnect-rssi: net::ERR_CONNECTION_RESET...
I am experiencing strange behavior on the PCA10056. I have two boards now in the same state, both were working fine before starting work on the Secure DFU (uart). The following...
I found that App timer using in ble_app_template in different modules. Is it possible to change prescaler value without harm to other modules? I need to increase maximum value...
Respected nordic community,
I am working on one project where right now i try to make custom service read operation through nrf52832 in segger studio. From my device(mobile...
HI, I am seungwoo
I am developing data transmission using nrf52810.
A 300-kilobyte file is divided into 220 bytes and transmitted continuously.
11-27 17:24:24.416...
Hi,
I'm developing a unit which i need from time to time to send a packet throw I/O lines (F.E.virtual uart)
However the packet bit timing is very critical.
As far as...
Hi, I am using nrf52832 with SDK 12.3.0 and nrf 52 dev board. I am experiencing a problem whenever I programmed nrf 52832 using nrf52 dev board and NRFGO, after certain number...
Hello, I'm currently using the nRF51DK with Wireshark as a BLE advertisement sniffer. So far this setup has worked great, but I'd like to make a small modification for development...
Hi all,
i am currently working on 5 nrf52832 DK boards, i want to use nrf mesh for indoor positioning system. I am currently using nrf sdk v15.0.0 and nrf mesh v2.2.0. ...
Hi.
We are on early phases of getting UART DFU support for our product. However I seem to run into communication issue with the bootloader even with the examples provided...
Should the DEBUG compiler flag be removed before flashing a board that should enter sd_power_system_off? I've seen some troubleshooting guides mention that Debug mode can...
I have set up the thread border router. I connected the NCP (a nrf52840) with a usb cable to a raspberry pi. Now I wonder if it is possible to connect the raspberry pi with...
Hi all,
Currently, I am working on Nrf52 DK with nRF52832 on Keil IDE. My focus is MQTT with 2 nRF52s and RPi. I have succesfully used examples in SDK, but now I am trying...
