I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Question 1: I am using GPIO external interrupt. Does this interrupt belong to GPIOTE PORT EVENT by default? Question 2: How to configure low precision GPIOTE? Question 3:...
I use NCS2.5.0，and I noticed that there are two files(bluetooth.h and scan.h) can help to set scan parameters.Is there any difference betwen these two files?Can I call the...
Hi,
This is my first time designing RF section for BLE using nRF54l15, and i was wondering if you guys can give me some feedback on hardware design. I chose a Johanson 2450AT42B100...
Hi,
I am trying to optimize my nrf52840 application for power consumption. If I run simple loop using nrf5 SDK i get ~1.2mA. However with similiar code on Zephyr: I get...
Hi,
I am developing a small beacon application using the nRF 52805 device, and the intent is that it will send advertising packets at a slow rate, to indicate to a partner...
I'm working on implementing arithmetic operations using the PKA engine on the nrf52840 in Rust, following the CRYPTOCELL — Arm TrustZone CryptoCell 310 datasheet. While I...
Hello all,
I have been working on the implementation of the PKA engine on CC310, and have been encountering some unexpected behaviours when using the modular multiplication...
Hi,Nordic team
I am programming with nrf52833,ncs v2.9.0,base on peripheral_hids_keyboards and central_hids.
On central I call bt_hogp_rep_write_wo_rsp can only send one...
I'm currently developing a project using the Audio NRF5340 to communicate over BLE. All the modifications I made to the Audio DK app work in VScode with SDK 2.9.0, but recently...
Trying to work through using the FLPR for a virtual peripheral. I can infer things like the VTIM sets counter 0 and 1 to automatically buffer data in/out via the VIO setup...
Hi,
I adapted the nus_client from the Nordic Connect SDK v2.7.0. I changed the UUID and some function names, but in general the code stays the same. I can subscribe one...
Hi,
What is the static current of nRF52832-QFAA at the temperature of 60℃ and 25℃ (when ADC ADC ,RTC are turned on, an IO port is opened for interruption)? I tested it at...
Hi,
i have some code thats based off of the uart_async_adapter.c example code. I' m getting a `usage fault` which i've traced to uart_irq_handler. it happens when i try...
Dear Nordic Semiconductor Support Team,
I am using the nRF52840 for distance measurement and have observed multiple distance-related parameters in my output, including RSSI...
