Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
NCS3.1.1, Windows10, VScode, NRF52840 custom board
With 3.1.1 I've discovered the paths in the "Edit build configuration" wizard are being broken and silently ignored during...
Hello DevZone,
May I know if there are any hardware SoCs and development kits that operate in Wi-Fi Halow(802.11ah) standard? Please point me out if there are. Thank You...
Hi,
I tested uart30 of NCS3.1.1, and found that I could not enter the low power consumption mode.But there is nothing wrong with uart20.
Related code usage:
prj.conf...
Hi,
I have a nRF5340 DK (PCA10095) that was working fine on the nRF Connect v4.2.1. I use the Direct Test Mode functionality.
However, after updating to v5.2.0, the DTM...
Hello, I’ve been exploring DECT NR+ on the nRF9151-DK using the DECT modem firmware. As it was already mentioned in multiple threads/other sources, there is no GNSS or LTE...
Hi,
I need support to get my brand new nrf9151 development board LTE connection up and running.
I have bought this kit and it came with 2 SIM cards as per documentation...
I have an FTDI USB to dual RS232 adapter for communication over UART. The nrfutil device command finds it in version 2.8.5 and below:
Starting with version 2.8.6 it doesn...
Hi,
In our custom nrRF9151 application we sometimes get a modem fault. This happens randomly when the device is moving, so likely something to do with changing cells....
Hi,
We have a client using one of our products, and their local NB-IoT network was giving us some issues, I travelled over to try and work out what was going on, and it...
So my board uses uart00; I also need to use ZMS for storing configuration data.
If I try to compile with no SPI enabled the Flash drivers throw an error '__device_dts_ord_130...
under freestanding applications, which code to use to enable bluetooth on nRF52840 DK kit . Then, it has to pair with android mobile. how i can achieve it.
Hello,
I am configuring the Watchdog Timer (WDT) on my custom device and observed that it gets disabled when the system enters Deep Sleep mode. This behavior prevents the...
Hello Nordic Support team,
I'm receiving the Transmission failure and Lora Initialisation failed message despite to correct wiring and everything else. I'd attach a link...
I've been trying to get SPI slave running on the NRF54L15-DK for over a week. I am new to Connect SDK but have successfully completed this task with NRF52840-DK (and dongle...
