I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi,
I'm trying to write data to a characteristic. This is a BLE led driver. I can successfully send 5 writes and then it stucks. All the 5 sends succeed - I can see the...
Hi
I need to Send one character from mobile. based on the character I need to glow the LEDs which is placed on DK. How can I achieve this is there any sample available for...
Dear forum,
We capture audio via PCM (10kHz, 8bit => rendering a raw rate of 80kBaud) on a BM833 and would like to transmit the data (one way) to a paired device using either...
Hi,
NCS1.9.1, VSCode, nRF5340DK,
Without external flash memory and not use mx25r6435f which on DK,
how does MCU store data (such as a series of serial numbers)?
and...
hi ，i want write flash by jlink，eg：write val 0xaaffffff to addr 0x76000, only write 4byte.
but when i write, err "flash not erase" occurred，
I don't want to erase this...
I try to onewire communication for DHT11 but I couldn't it . I decided uart instead of onewire. The different microprocessor will read the sensor data and send it via uart...
Hi,
I'm trying to combine OpenThread, MCUBoot and LittleFS in a sample in nRF Connect SDK v1.5.1, but I'm getting the following error:
I have checked the file, and it...
Hello NRF Buddies,
My project is based on NRF51822 with SDK version 12.2.0. I am working with Keil till now and planning to migrate to the Segger Embedded Studio.
With...
I am not sure what I am missing in this. This is a custom board so there is no other circuitry on this pin other than a pad to monitor the signal changes with.
When...
Hello!
Regarding the CRC on the nrf52840 the specifications make it clear that the maximum length of the CRC is 3 bytes, We are working on an industrial communication protocol...
Hi
How can I readout the actual timer value on the fly? I use the timer in capture compare mode and like to read out the timer value.
nrfx_timer_clear(&m_pyq5848_timer...
Hi all,
I have set up an nrf52840 as the sniffer to sniff the connections between my custom board and central phone. My goal is to figure out the bottle neck of the ble...
I based my project on the secure wireless uart example in the nrf5 SDK and linked to the precompiled gcc library 802_15_4_lib_gcc.a
I then tried to add multiple entries...
It seems that once we install nRF Connect into VS Code it completely takes over and now when I open any file in VS Code I see all of the nRF connect tabs and controls which...
I'm trying to debug an application however there is no documentation on how to set up the debug.
How come nRF connect is selecting the HEX file. I want it to select the...
