Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Good day
Our custom board contains RS485 implementation. The file schematic for that looks like this:
I have noticed that a driver and sample exists but the driver doesn...
Hello everyone, I'm currently updating my project from SDK v10 with softdevice S110 to SDK v17.1 with softdevice S132 (a huge step). I'm, wondering if what I want my code...
Hi
I am trying to make a SPI connection with a device which doesn't already have a driver build into Zephyr.
Is there some kind of genereic device i can use since i just...
Hello,
I am trying to send data from a delta-sigma 32 bit ADC - the front-end is an EEG amplifier - via WI-FI to my broker. I would like a recommendation related to the...
Hi,I am using NRF5340 AUDIO DK BOARD and I have been trying to access i2s mic and I want to transfer the mic data to Amplifier .Is it possible to do with single I2s ? As I...
Hello everyone,
I'm experiencing some issues while trying to program an nRF52832 CIIA on a custom PCB. Specifically, I cannot get the GPIO pins or the external 32kHz crystal...
Hi, I checked DFU over Wi-Fi in a separate project (net/download) that only included DFU and Wi-Fi-related functionality. In which FOTA is working as expected.
In our custom...
I have just started programming the using the nrf52840DK_nrf52840. I downloaded the toolchain and sdk using the VS code extension and created a new application from the blinky...
Hello,
I just upgraded from v2.5.0 to v2.7.0 of the SDK. To do this, I had to modify my files of my specific board and use sysbuild.
My project compiles and works on my...
Hi All,
I'm considering using the nRF5340 in an audio application. I'd probably go for a 3rd party module in order to avoid getting FCC certs on my own. Possibly the Fanstel...
In Section 6.17.1, page 543, of the nRF52840 product specification version 1.10, in regard to the Pulse-Width Modulation (PWM) peripheral, there is a statement that says ...
Good morning,
I am try to build a application from example list, Bosh bme680 with supported board rak4631_nrf52840, and I am receiving a error message, but if I try to...
hi ,
I am currently developing a project using the nRF52810 as my controller and SEGGER Embedded Studio (version 5.42a) as my IDE. I have successfully integrated the Timer...
Hello
I want to make an application based on the multi NUS sample https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/enter-the-multi-nus-a-simple...
Hello,
I am practicing the intermediate Nordic Academy online course, and I have a problem of the thread viewer.
I have enabled debug, I did everything strictly according...
