Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi Guys, trying since some weeks to develop an " simple " Gap advertising with only 2 "service Data" ( battery level and an ID of 4 bytes with an uuid of 128bits with Mbed...
Hello.
I run a project on RTOS base on embOS of Segger. Now I want to add a BLE task base on Nordic BLE peripheral UART. As a standalone project not on RTOS it is run O...
With mesh dfu, whether to upgrade the firmware of many different devices at the same time is supported. Multiple device deployment spaces are adjacent, and simultaneous transmission...
How to fix this error: Installnnnnfgo Studio tips can't find nrfjprog.dll The development environment is: windows 10 Pro 64-bit operating system MDK-ARM Plus Version5.20 nRF...
Hi,
I am in the process of converting a large freertos project from nRF52832/SDK14.2 to nRF52840/SDK16.0
I've managed to convert everything but the buttonless DFU...
I seem to be getting odd behavior of the UARTE0. Actually, this same behavior happens with the standard UART0.
I have a loop that sends a two byte message every 1 second...
Dear Nordic Support,
I just got my Thingy:91 and I followed your Getting started guide. I registered the SIM card successfully but whenever I reached this step, it always...
According to the nrf52810 v2.1 data sheet, the radio draws 7.0 mA at +4 dBm TX power and 4.6 mA at 0 dBm TX power.
How much power is consumed at transmit levels from -4...
I live in Vietnam, I try to use NRF9160 dev board to connect LTE and NB-IOT but device cannot connect to the LTE/NBIOT network. I am using the at_client example with nRFconnect...
Hi
I am using fafs example from SDK 15.0.0
It was possible to write to the SD card by SPI communication. However, using SanDisk's 32GBSDHC, it became impossible to write...
Hello
I have both mai.c and app_sdcard.c "static const nrf_drv_spi_t spi = SPI_INSTANCE (spi_instance);" Want to use .
So using "extern"
main.c
app_sdcard...
I have already developed a beacon with nrf52840, but now I need to detect it with another nrf52840, but my problem is taht I need to use less power as possible, so I need...
Hi guys, after building and running a mesh network i've been wokring on, i ended up with an error
im wondering where i'd be able to find the mesh error table.. i can't...
I have custom board with BMP280 sensor & nrf 52832.I have interfaced BMP280 using twi interface. I am using SDK 15.2.0. and soft devices s132 V6.1.0 to transmit advertising...
