I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
We are working on a project using the nRF5340 with SDK version 2.4.2. We have integrated a NAND flash using standard SPI communication, utilizing the QSPI-assigned pins...
Hello
I am planning to design a custom board for my battery operated application and for that I need 5GHz Wi-Fi, Ultra lower camera. I need suggestions which camera is...
Hello,
I am currently working on a mesh sensor system. I have got one sensor board and one board for connecting in the mesh system. Now I want to be able to send the sensor...
Hi:
My environment is: nRF5_SDK_17.1.0_ddde560, keil, s113_nrf52_7.2.0_softdevice
When using usbd_cdc, I found that DTR must be set to start communication. Is there any...
Hi,
i develop my product ny ncs V2.6.0. in some case,i need store some user data to the flash,but i dont know how to read and write flash in cns sdk.if there is some samples...
Greetings.
Our team has encountered some difficulties in integrating nPM1300 into a new project. In the project we plan to use nPM1300 in conjunction with NRF52810. To develop...
* The nPM1300 LDSWSTATUS register @ Address offset: 0x4 doesn't contain values in the "Value" column.
* ID "E" occupies only one bit, but declares data on 4 devices:
...
We are planning to base a GATT and LE Audio design off of the latest nRF Connect SDK v2.6.1 and looking into Bluetooth certification. I have found the QDIDs for the Host and...
Hi, I try to launch west build command from a terminal.
I am first generating environnement variable as stated in this post :
Then I call it, and finally, I launch this...
Hello,
I am working on a custom board designed around the NRF52840. Currently the bootloader on the board is the same as the one on the NRF52840 DONGLE. It is out intentions...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
My goal is to achieve a data throughput...
We are connecting nrf boards to solar charged batteries for power consumption. We will be remotely deploying the boards on field. The boards are connected to sensors, from...
I'm going from v2.6.1 to v2.7.0; I'm using a thingy53. I'm getting a voltage error prior to boot.
[00:00:00.002,929] <err> voltage: setup: -134 *** Booting nRF Connect SDK...
Hello.
Wiring 1:
wiring 2:
Background to the case: We tested this with 2 different ppk2s and always got the same results. Our custom board works fine if we wire...