I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
I have define CONFIG_NFCT_PINS_AS_GPIOS, but the pin is always low, even if the OUT register is high.
I have read 0x1000120C(NFCPINS), it is FFFFFFFF, what's wrong with...
Hi, After many attempts I was unable to make RPC_Host sample work ( link to the related nRF Connect SDK doc ). From SES in debugging mode, the network core gets stuck in an...
Hi,
I am writing a program to actively change the state of an LED, then sample the output voltage on the led pin using SAADC, then outputs the adc value to terminal every...
I bought the nRF52840 DK and want to start developing my first application. However, I am very overwhelmed by the documentation here infocenter.nordicsemi.com/index.jsp This...
Hi All, I have a problem with the UART interrupts on the nrf9160dk, the error code (-134 / -ENOTSUP) says that it is not supported. However, I don't know what might be the...
Hello everyone,
I'm unable to perform DFU over SMP BT with nRF Connect for iOS. I've already verified the process works with mcumgr (Ubuntu 20.04 LTS) and with nRF Connect...
I am trying to use the `fmfu_smp_svr` sample project, as described in nRF9160: Full modem firmware update using SMP Server , to perform a full modem firmware update.
The...
Dear ,
I am going to use SDK 17.0.2 spis example.
But I found it is 8 bit data width. I am going to use 16 bit data width .
Would you teach me how to change?
Hi all,
I am using NRF5340, and I want to use pin 0.14 for spim. However, I found it was used by QSPI, in zephry.dts:
So how can I close QSPI to use pin 0.14 freely...
Hi.
Below is used the same schematic for nRF52805 but with different placement for RF components.
What are the pros and cons of each one? Is there one that is "better...
Hi !
I want to successfully send CTE after the CRC of the broadcast packet by operating the RADIO register under the Manual configuration of NRF52833。At present, I can successfully...
Hi developer,
I am trying to understand Beacon behavior and program. I am using BLE_Central multilink example to get informaiton from Beacons.
I added the below code...
Hi, I tested the (mcu_boot + smp_svr) example and can run dfu successfully with nrf_connect application. (Follow the page: developer.nordicsemi.com/.../README.html) Now I...
Hi Nordic,
One of my custmer want to develop multiperipheral product(The device connect to two central devcie).
The nRF52832 can certainly meet their requirements, and...
