Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
Hello,
I'm working on a custom board with a nrf54l15 chip.
I would like to add an interruption on the GPIO P2.10. But I get an error -ENOTSUP with gpio_pin_interrupt_configure_dt...
Hi Support Team,
I tried several ways to set the image version but failed. My SDK is ncs V2.5.2. 1. set(CONFIG_MCUBOOT_IMAGE_VERSION "1.0.0") in CMakeLists.txt: did not...
Recently I've had an issue with 3 of our nRF9160 based products during production (several hundred of the same hardware/firmware/SIMs work fine). The issue is that while the...
Hello Nordic support,
My application is a Zigbee coordinator application on nrf52840 based on nRF5 SDK for Thread and Zigbee v4.2.0. I was able to pair a Zigbee end device...
I am using the Zephyr SPI driver to control a WS2812 LED strip through the SPI interface. Since only the MOSI line is required for communication, I want to configure the SPI...
I am developing a device that uses ESB.
Uses modules that are Telec and FCC certified with BLE profiles. (module : MDBT50Q-512K)
I have a few questions.
Q1. The TX power...
I have two boards:
nRF52840 DK (which has a faulty buck converter, so I am powering it via USB).
Fanstel BT840F board , which provides power to the Debug In connector...
I used nrf5340 on my board and did some changes based on audio demo.
Unfortunate,I heard a noise after set configure like bis gateway, audio input from usb ,48k 16bit 2channel...
Hi,
I have a problem with unmodified BLE Shell and changing security level to 2(aka just works).
1. I'm connecting from BLE Shell to the device that requires level 2 2...
I am attaching an adapter board to the nRF52840DK to debug a custom board.
However, if there is any contact failure on the adapter board, the nRF52 on the DK will be the...
Hi Support Team
1) Does the new nRF54L05 chipset need to recover before program? We execute command line nrfjprog --recover but it is unavailable for nRF54L05. And nRF54L05...
Hello,
I am developing matter sensor and I would like to send data to `MeasuredValue` attribute of `CarbonDioxideConcentrationMeasurement` cluster. I followed this tutorial...
I have an nRF54L15DK and a custom-designed nRF54L15 board. These two boards use different pins for peripherals. The NCS version used is v2.9.0. I compiled a Matter project...
