Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
I am using SDK 3.1.1. I am trying to use the "sensor get" command with the internal die temp sensor.
In theory, this is all off the shelf software. I didn't write anything...
While running scan & connection tests with NCS 3.2.1 , I encountered frequent connection timeouts ( bt_hci_core: Connection creation timeout triggered ) when using the Nordic...
I'm using the Power Profiler Kit II to measure current draw of an ESP32 board at idle. The PPK2 is connected to the battery terminals of the board (XIAO ESP32-S3) and whether...
Hello, I should like to enquire whether the nRF54L15-DK development board supports both Classic Bluetooth and Bluetooth Low Energy. Having reviewed the relevant documentation...
Dear All,
I'm following the nRF Connect SDK Fundamentals and I have a weird problem in the Lesson 3 exercise 2, section "Adding custom configurations".
The part with...
Hello everyone,
I've been testing the "central UART" with a "peripheral UART" (NUS) examples with two nRF54L15 DKs (nRF SDK v3.2.1 in VS Code). So far, everything is working...
Hello everyone!
I have a question regarding nRF9151 and the new DECT Hello sample. I have installed the newest version of the SDK, a preview of v3.3.0, built and flashed...
Hi!
NCS 3.1 On a custom board with nrf5340 and nrf7002, h ave successfully implemented and tested FOTA over Bluetooth Low Energy with Simultaneous updates for both cores...
Hi,
I'm trying to reduce the power consumption of my Matter Temperature sensor code.
I'm averaging around 90µA of consumption, but I'm confident that can be reduced. ...
Hi,
I’m having trouble getting an ISP1807 (nRF52840) to run on a custom PCB, and I’m hoping someone here might recognize what I’m missing.
Hardware / setup
Module...
Hello, we’re currently facing an issue regarding the start-up of the nrf9151 modem. Its a custom PCB and closely follows the schematic of the nrf9151 DK. For first test SW...
Hello Nordic Engineer,
I know that I can modify #define DEVICE_NAME "device001" in sdk_config.h , but it takes a lot of time to compile and flash the program every time...
Hi,
I have flashed hci_usb example on nrf52840dongle(hci1), enabled DLE. But when linux machine requests data from other board(as sender) dongle is getting crashed.
The...
I have create a model (which is now marked as complete), but when I go to the results tab the options (and below) just show a spinning circle. How can this be fixed?
