Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
I have a problem understanding notifications/subscriptions in the BLE context.
I have two devices, Central (nRF5340) and Peripheral (nRF52832). My peripheral provides a...
This not a question. It is for your information (FYI). I've seen many questions about flashing the nRF53 using CMSIS-DAP. Anyone interested see attached instructions.
The...
Using an approach similar to what's in the ble_app_att_mtu_throughput example, my goal is to transfer data as fast as possible. (I.e. call sd_ble_gatts_hvx() on the same characteristic...
I'm building the nrf/samples/openthread/cli sample with the nrf54l15dk/nrf54l15/cpuapp/ns board. The only change I'm making is enabling CONFIG_DEBUG_THREAD_INFO.
The app...
Hello,
I am using an LE audio code "nrf5340_audio" code from nRF SDK v2.8.0 to play a beep tone. I want to play a tone from a temporary memory, so I have created a logic...
I'm following the dev academy lessons and I'm having a bit of an issue where VS Code intellisense isn't picking up on the include paths from zephyr (e.g. #include <zephyr...
Hi, while working with the nRF9160DK i get this Error a lot of times, I can't say "Yes" or something else and have to wait until the progress bar fills completely. Even if...
Hello
Our 52840-based device has a functionality of playing one of 10 pre-recorded phrases via I2S interface. We'd like to be able to update the wording or load a different...
When integrating DTM into my main app, I have to comment out the macro CONFIG_BT=y to ensure the DTM test can run properly after the build. Are there alternative ways to include...
Hi
I am working on nRF54L15-DK (PCA10156 0.9.2 2024.49) with chip N54L15 QFAAB0 2444AA
I am using Nordic SDK 3.0.2 and Zephyr 4.0.99
My task is to have the top 2K of...
Trying to read button 3 on the npm1300-ek, which is gpio 1 according to the schematic. The following #defines represent the gpio related registers on the npm1300:
#define...
I have been using my nRF54L15-DK board since it arrived just fine, however today when I went to flash the firmware I received the following error:
-- west flash: using runner...
Dear All, I am looking to connect to WiFi enterprise AP. So far I have been able to connect to the network using the nrf/samples/wifi/shell using a command that looks like...
Setup: SEGGER and running S112 & nRF5_SDK_17.1.0
Don't want to delete all bonds, only the specific one.
Bonded with Android and Apple smart phone
Delete pairing information...
Hi there.
Does the nRF52840 require any protection on the Bluetooth Antenna Line needed to block large unwanted signals when fitted on a Modem that also incorporates GSM...
