Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
Hi,
I've got a lot of BLE_GAP_EVT_TIMEOUT when my ble central trying to connect with BLE peripheral (sometimes more than six in a row).
The configuration of my system...
HI,
I have couple of questions here.
1.Is there any sample application that upgrade firmware over BLE using zephyr/NCS 2.1.0 for nRF52840
2.If so our requirement is...
We are using QSPI XIP mode to access data in external flash for our project. We are trying put QSPI peripheral in standby mode.
However, we can't uninitialized QSPI peripheral...
I want to develop a device with the following selection.
BLE module: Raytac MDBT42V (nRF52832)
nRF Connect SDK v1.2.0
Where can I check the version of SoftDevice...
Good Day!
I have a Samsung Note 10 smartphone (it supports Long Range) and I want to connect it to an nRF52840 microcontroller using BLE Long Range.
What is the approximate...
Hello
I was using the NRF52840 dev kit as J-link to develop a custom board. at first was working, i uploaded a blink code to it then i modified the libry from gpio.h to...
Hi,
We used the SLM (serial LTE modem) application in our custom board with NRF9160 configured as a slave chip and interfaced with an STM32 MCU via UART interface. The SDK...
Hi there,
Currently developing a producting using two nRF52833 boards one as peripheral and one as central:
- 125kbs coded phy (S8)
- 40 byte MTU
- using extended...
Dear Nordic Engineers
I have a question, it about SPI PIN input voltage of NRF5340.
Our cutsomer use NRF5340 and STM32 develop a product. STM32 and NRF5340 use SPI to...
Hi, we will shortly be sending our product to an independent lab for testing. They have asked us to provide any available documentation/certificates that apply to the on-chip...
I used the NRF52832QFAAE1 chip for Bluetooth development before, and later changed it to NRF52832QFAAE0 to use the same software program, but NRF52832QFAAE0 can download the...
Hi Team,
We are trying to store the audio that is being captured and transmitted by nrf5340 digital mic and then store it to connected android phone. For this we tried A2DP...
I test data transmission through NUS service as follows.
If data is transmitted 6 times in succession, the system crashes. No logs appear. However, the system does not die...
I would like to measure the current consumption of an nRF21540-EK (mounted on nRF5340-DK) using the PPK 2. I can't find any relevant documentation regarding the connections...
Dear sir or madam
We are designing a new project and need to transmit 2 Mbit/sec of data, wirelessly.
We would like to get your recommendation about a device and a protocol...
