Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
in main.c, you have this code
but if you set CONFIG_BT_NUS_SECURITY_ENABLED=n in the prj.conf file, then there are #defines that will prevent the definition of the...
There are two DKs, one works as a slave while the other works as a master. When these two peripherals are connected via Bluetooth, they exchange each other's parameters via...
Dear Support Team
Our customer prepared to develop a triple mode operation game keyboard which communicating over Bluetooth LE, either via the dongle or USB. Should the...
Hello, thank you for taking the time to read this.
I've been reading through some of the forms, and I'd highly appreciate someone with more experience giving me some input...
Hi Support Team,
I’m designing a custom PCB using the nRF52840 based on "Circuit configuration no. 6" from the nRF52840_PS_v1.0.pdf. On our design, VDD_nRF = 1.8V which...
Hello,
I'm making some sensors based on nRF52832 and I'm using them as native transceivers. Maybe I'll look at BLE Mesh in the future but at the moment I just send and receive...
SDK 17.1.0
I developed a firmware that can be used in nrf52833-CJAA-R, but it can't be used in the nrf52833-CJAA-B.
According to the following link:
devzone.nordicsemi...
Hi Nordicsemi Team,
The one of our customers recently purchased NRF52-DK (Dev. Kit) which was Ver 2.1.0.
But This time has issue. He thinks after version 3.0.0. cause...
Hi, I am currently trying to use PWM on nrf9160 DK to control a stepper motor. Do you have any sample code for PWM? Also do you have the pin assignment of which pin on the...
Hello! I am working on a project I have set " sensor/server" as my starting point. The sensor is successfully interfaced with NRF52 I need to store the calibrated data of...
We're trying to develop a device driver by putting it in our application folder (under /drivers).
The west build system now recognises and builds it through the Kconfig...
I am following the instructions to set up NUS shell through bluetooth with the following example: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth...
hello
I try to make work the ADC on the NRF52840DK
I would like to use any of the 6 channels on the ARDUINO connector (p0.3, p0.4, p0.28-p0.31)
I am simply not able...
Hi . We have been struggling for months now to achieve DFU updates for our firmware with no success. On our latest stage we get "Can't find room for update". We are just trying...
Hi,
I have a very high consumption when using the ADC of the nRF9160, I am using the NCS 2.0, the firmware used is inspired by the sample provided on github below:
https...
