Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
Hi
How do I configure a custom child image for the network core on nrf5340dk? We're using Zephyr RTOS, and want to do a multi image build when building the application ...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Hello, I would like to know if the Power Profiler Kit II could be used to measure current consumption on the Thingy:91 ?
In the Thingy:91 documentation, it is suggested...
I want to add a simple GPIO pin that act as output pin, in the peripheral_uart example .
in main.c
#include <drivers/gpio.h>
//#define GPIO0_LABEL DT_PROP...
I'm using ble_app_uart_c project in nRF5 SDK 17.1 with SES.
I got 2 different devices, one is ARC EM9D AIoT DK (as Peripheral) and another is nRF52840(as Central).
I was...
Hi,
nRF9160 with SLM NCS v1.9.1 fails to attach after 7th RESET (by RESET pin) & attach without power cycle.
There is not any ERROR state reported by modem, modem fails...
Hi All,
I am using s112_nrf52_7.2.0_softdevice with nRF5_ SDK_17.1.0 and Segger Embedded studio for nRF52805.
My application code is successfully patched for nRF52805...
Hi,
I'm using the default software to check the acceleration values when there is a movement in the Thingy:91 on the LTE Monitor terminal.
The document says that this...
Hi,
I want to test of MQTT communication with nb-IOT network before going for development.
For that I have updated pre-built firmware on development board using nRF...
Hi,
I'm using nRF52840DK with a UART peripheral (on SDK 17.1). I'm wondering what's the right way to handle UART error. Every time the peripheral power cycles, I'll get...
Hi,
Getting this error using the latest version of pc-ble-driver-py on Mac with the latest version of Catalina for the example application heart_rate_collector from the...
Hi I've been trying to get into Nordic's ecosystem using their SoCs but it's been a huge headache. Probably because they don't have their own IDE (like Microchip and STM have...
I have looked at few previous posts regarding integrating ble hid mouse and ble hid keyboard. But of no use, still stuck.
I have seen the following posts already
1) https...
In my device that uses NBIOT I am modifying the FW to use LTEM.
During the tests I have shown that the consumption of LTEM transmission for the same amount of data sent...
Hello, I'm looking for a BLE module with its integrated antenna that works with NRF5340 so far i didn't find something using Nrf5340 other then the UBlox Nora B-106 All the...
