Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi，
In the NCS V2.3.0 version, I successfully obtained the serial device through the following code and compiled it But when I get the serial device in the same way in NCS...
Hi,
Sorry to be posting a lot about my LIS2DH12 on custom hardware lately. I do believe my different inquiries are to be treated as separate.
My (modified) hardware now...
EDIT: Sorry to be posting a lot about my LIS2DH12 problems lately, as I'm advancing somewhat while I have open support threads. Newest thread is here: In preparation of this...
Hi,
I'm using nRF5340 Audio DK with the audio example code in BIS mode. I would like to set the broadcast name during runtime, and not before compilation. Namely, I want...
Dear support team, We need to integrate DTM function into matter. We have disabled bt, but it still prompts that radio_init failed. Do we still need to disable matter protocol...
We are trying to setup image encryption in our nRF build, for use with BLE DFU.
I see that this is not supported by Nordic, but that there is support for it in MCUBoot....
I want to add the timer sample code to my own project "../src/main.c:11:10: fatal error: nrfx_example.h: No such file or directory 11 | I'm encountering the error #include...
| Host | <---- UART ----> | nRF52833 (central) | <-- BLE--> | nRF52833 (Target) |
I have a requirement where I hope to update the central's firmware image through the Host...
Hi,
I am using the NRF52832 DK version 3.0.0 with a UWB module: the DWM1000 from Qorvo.
I was struggling with the SPI communication to get the Chip ID by sending a simple...
Hello,
I am working with nRF52832 and want to put it to sleep and wake it up with a interrupt from a GPIO. I am using a accelerometer LIS3DH to generate the interrupt. I...
Hi,
We're using nrf Connect SDK v2.4 and have issues when calling bt_gatt_notify() from our main thread. The bt_gatt_notify() function blocks even though we have the CONFIG_BT_L2CAP_TX_BUF_COUNT...
I merged two sensors, BME and BMI, and checked the raw data output through NRF_LOG_INFO. Now, I've added the new merged code to the main firmware, but the log for the BMI...
Hi there,
I have multiple flash partitions defined in pm_static.yml.
I want one specific partition to contain a binary data file so that when I flash the image with J...
Hi all,
I am developing a project with the nRF52840, using nRF Connect SDK 2.6.1 in Visual Studio Code.
I need to be able to compute an MD5 checksum for a dependency....
