Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
I am unable to see any options on the welcome menu for nrf connect
The menu was working yesterday,
I have uninstalled and re-installed and tried a previous version.
...
Hi,
we're developing BLE sensor platforms with 10+ sensors on a device. We have some bandwidth issues if we connecting more than one BLE device to a BLE host:
For Example...
I am using the IQ values collected from the Channel Sounding example. The data in the 0 section seems to indicate that this channel is not in use? For example, as shown in...
Hi, I see this goes back at least as far as v2.4.4 and still exists in v3.1.1. Around line
if ((!err) && (err != -EALREADY)) { LOG_ERR("Stop LE scan failed (err %d)", err...
nRF52840 datasheets says it supports 3 SPI slaves, but I need 4 SPI slave devices on my next design (the current design uses 2 SPIs). I don't need DMA transfer at this moment...
I am trying to implement Attribute caching as described in Vol 3, part G, section 2.5.2 of the Bluetooth Core Spec .
Reading the GATT Database Hash seems to work:
The...
Hi Nordic team,
I’m working with an nRF9160-based device and have observed inconsistent LTE behavior when the device operates in areas with poor or unstable signal strength...
Hi,
I want to synchronously get data from different nodes.
Can BLE mesh obtain information from multiple nodes simultaneously? I would like the collected data to have...
Hello,
Using nRF Connect vscode extension, vscode is very slow and almost unusable.
The following process is started multiple time and i have an instance taking 100...
I have an issue with the Lightness setup server set cb being triggered without a connected device and is not internally called in my code. Yet for some reason the set cb is...
Hi
I noticed nordic provides Wi-Fi: Throughput to evaluate the throughput when device is working in STA mode.
If I want to evaluate the device in AP mode, is there any...
Hallo, we are evaluating the UART peripheral of the nrf54l15. As a first step, we are trying to get two DK to communicate with each other, unfortunately without success. ...
Hi all,
I'm looking at an issue and I can't get my head around it. I clearly do something wrong here but I'm stuck.
On our nRF54L15 DK we have a program that can show...
Dear Teams,
I’m using an nRF9151DK board running a simple firmware (example link: github.com/.../ subsys /pm/ device_pm ).
I connected a Power Profiler Kit II (PPK2) to...
