Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
I’m working on a project using the nRF54L15 SoC together with the nPM1300 Power Management IC . In my hardware setup:
BUCK2 output from the nPM1300 is connected to the...
I currently evaluated the use of the "<modem/at_parser.h>" (at_parser module).
Using it with the at-cmd "at+CEINFO?" is very irritating.
I 07.324 : CEINFO: +CEINFO: 0...
Our team is transitioning to the nRF Connect SDK after extensive experience with older nRF SDKs and custom build systems (based on cmake + west + python) integrated with VS...
I would like to know if in mesh device for the comuniation are used all that channel or only the 3 channel that are used for the advertising channel or all the channel 37...
Hi
any one a clue why I see this bar twice?(see attached picture)
Some thing probably went wrong with my previous older installation.
I already reinstaled Wireshark...
I'd like to call a function on the peripheral (by pressing a button or sending a command from the terminal) that performs unbonding from a central. I'm able to bond using...
We are looking to migrate our nrf52833 project to latest toolchain and SDK for build in visual studio.
We use MCU boot, BLE and Zephyr RTOS.
Do we need to follow each...
Hello,
i'm facing errors when trying to build matter sample thermostat.
I doesn't matter if i use VS Code or terminal
(v3.1.1) C:\ncs\v3.1.1\nrf\samples\matter\thermostat...
Dear Nordic Supportteam,
starting from the ESB sample I have developed a transmitter and a receiver application, both running on a separate nRF54L15DK. My goal is to find...
Hello, I am having a problem with Exercise 1 of the Cellular IoT lessons (nRF Academy, Asset Tracker Example). I have carefully followed all the steps outlined in the documentation...
Hi
I experienced higher sleep consumption after enabling CONFIG_PM_DEVICE. I reduced the project to the minimum and it seems that the combination of an enabled uart and...
Hi! I started designing a PCB for the nRF54L15 radio chip, which I intend to use for ESB communication between two relatively close-together (<10 meters) devices. I've been...
Hi!
How do you recommend to debug crashes?
Especially how do you recommend to debug crashes that happen to our customers that we cannot reproduce?
So far I have been...
In order to develop the most effective power supply possible for the nRF9160 SIP, I need to know both the maximum current consumption of the nRF9160 and its duration.
The...
I’m using nRF Connect SDK v2.8.0 and working on BLE OTA (DFU) for the nRF7002 DK . I followed the Nordic “DFU with external flash” exercise and integrated it into the Wi-Fi...
