Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
We are implementing a system where diagnostics info is saved to FLASH when one of the error handlers is called. Our code collects diagnostic registers and stack info, and...
Hello,
I am working on a driver in which it needs to transfer larger sets of data over a I2C connection. However, I am getting this:
"Cannot copy flash buffer of size...
Hi，
Q1: SDK for PCA10112:
I'm trying to evaluate 21540 DK and EK set. Where do I get sample code that compatible with PCA10112? I've checked the latest nRF5 SDK 17.1...
There are several questions regarding this, most recent I could find from 6 months ago ( https://devzone.nordicsemi.com/f/nordic-q-a/81686/is-there-support-for-gatt-caching...
Hi,
I would like to know if I can update the firmware of modem from 1.1.1 to 1.3.1 on Thingy91 (hardware version 1.4.0).
My goal is to use AGPS and PGPS assistance services...
The product specification states that "o nly the dedicated QSPI pins shall be used. " Is this a recommendation or a requirement? I would like to configure a different pin...
I accidentally closed the original ticket , so I create a new one.
Hi,
recently I'm building dfu function on my board, using nrf51822 qfaa and softdevice s110.
...
hello,
Im using nrf52840 Im trying to emulate a chip select signal for spi slave with gpiote and ppi. I used an active high signal as an event and a signal(cs) that is toggled...
Hi everyone,
I have some questions regarding RSSI:
1. Is there any Bluetooth reference that evaluates the RSSI? For example what RSSI range is considered as perfect, moderate...
env:
SDK: nRF5_SDK_17.0.2_d674dde
KEIL- ARM
SoftDevice： s140_nrf52_7.2.0_softdevice
i can't understand how MBR jump to bootloader, and how MBR konw the start address...
I'm using SDK 17.0.2 and I'm trying to write a small central device. It should connect to a single peripheral and exchange some data.
Once the peripheral is found, central...
Hi,
I am trying to get access to the code 1.99.99-dev1 branch of the NCS, but I'm not sure where I can find this. More specifically, I would like to use the code of the...
Hi.
I am developing a small notification monitor.
It used a 150mha battery and a 0.92 oled.
I want it to be connected to my phone via Bluetooth and when I send a string...
Hello DevZone,
I have a project where I want to use NFCT for communicating and charging. I have used the NRFX_NFCT library to read and write to my transmitter because...
