Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
I adding custom pins declarations through overlay file as in first image with corresponding yaml file ( see attachment) with path .. /dts/bindings/gpio/custom.yaml. The project...
Good Day. I am wondering if anyone could maybe assist me in where I am going wrong with my software.
I have the intention of using a Nrf9160 as a serial modem through AT...
I use nrf9160 to develop a product for customers. The modem is also set to PSM and the log is turned off. However, I find that when the modem is connected to the Internet...
When I try to connect to nrf52840 using J-Link, the following error is detected.
What is the reason for this "Failed to power up DAP"?
- Connecting via USB to probe/ programmer...
Hello nordic support:
We want to measure nRF9160's LTE RX SNR at production stage .
According to the document nwp_034--nRF9160 Hardware.pdf ==> 4.6.1. Following command...
Hi, I am working on nRF52832 as central. When I program it to form Segger Embedded Studio it's working fine but when I upload that .hex file from the nRF Connect device did...
Hi there,
We are designing a coin cell (3 V nominal) battery powered product; we'd like the ability to run it all the way down to 2.0 V for maximum lifetime. To get the...
Board: nRF52833
SoftDevice: s140
SDK version: 17.0.2
I am trying to implement OTA buttonless DFU feature in my custom device (USB Device) which is a central device....
Hello,
I'm having some issues troubleshooting, my knowledge is limited on how to trace down where the error occurs.
Se logs below ->
Any tips on how to find...
Hi,
I start to work on the NRF52840 and I would like to read register of BMA400 in burst mode (I mean possibility to read further register in one sequence)
I am novice...
Dear Nordic,
when moveing the project to v.1.9.1 stack we've faced with a lot of
"fatal error: tinycrypt/constants.h: No such file or directory"
What is it related...
Hi folks,
SAADC peripheral gives me good results in acquiring & converting a DC signal related to current consumption.
I am using the 12-bits configuration over the internal...
I’d like to be able to read some environmental sensors and control some low power outdoor devices using the nRF52832. While I am aware that the nRF52 can operate for a long...
Hello,
NCS1.9.0 or NCS1.9.1 , Windows10 X64,VS Code,periodic_adv.default codes
with nRF52840-DK work fine.
but nRF5340-DK got error,as folow logs
"Failed to create...
