Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hello,
I am trying to send and receive data from an external slave sensor using the NRF5340. For debugging purposes, I have connected the NRF5340 to my PC via UART.
...
Hi all,
I'm working on a custom board based on the nRF9160 and using nRF Connect SDK v3.0.2. We’ve developed the board in-house and integrated the npm1300 PMIC as part of...
Hi, please bare with me for a newbie question:
I was in middle of learning the led_and_button example with "NCS fundamental" online video, and was trying to read code for...
Retrieving Custom Firmware Version from nRF52 BLE Controller to nRF9160 Host
Product: nRF Connect SDK v2.6.0 Hardware: nRF9160 (Host) connected via UART to nRF52832 (Controller...
I'm currently working through DevAcademy Lesson 5, Exercise 1 using the nRF9151 DK , following the CoAP client example. I’ve encountered an issue when attempting to POST data...
Hi,
We are looking to test the Skylo NTN network with the nrf9151.
We have NTN sim cards from Monogoto.
Do we need to load any special modem firmware to the chip? The...
Hi !!! Currently i am using Ncs 2.9.2 loaded with nRF Connect for Desktop and sdk-sidewalk is git clone branch 2.9.2 I'm trying to build samples for nrf52840 board to test...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
Hi,
I'm working on an application that combines both central and peripheral roles. My 'gateway' should connect to 2 peripherals and sometimes start advertising to make...
Hi,
we notice that the PPK2 doesn't like when we are letting it have the current reversed, ie when we are activating our PMIC to charge the battery.
This is a very good...
Hello,
I tested how "Direct Test Mode" app interacts with "direct_test_mode" firmware from "nRF Connect SDK" v2.8.0 (nrf/samples/bluetooth/direct_test_mode) and it seems...
Dear devzone，
Use our chip wdt module to feed the dog regularly. Under normal circumstances, if it is stuck in a dead loop, wdt does not feed the dog, and the wdt timeout...
HI all So currently we are researching the following configuration. We have a main MCU running Zephyr RTOS and its connected to nRF52810 over SPI. Ideally we would like to...
Hello i am running the radio_test sample on the custom nrf5340 board for the logging purpose i am using the pins 8 and 9 of the port 0 but the issue arising is that there...
Dear Nordic,
This post is successor of https://devzone.nordicsemi.com/f/nordic-q-a/122755/nrf7002-rfbuck-vdd-voltage as continuous of the work.
Although there are still...
