Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
I am on the learning curve of nRF9151 and LTE/GNSS.
Trying to build and run the sample app under nrf/samples/nrf9160/location
The errors Im getting are
[00:11:23.476...
Hi, I have upgraded my custom nRF52840 devices from SDK 2.4.1 to SDK 3.0.2. For few days, these devices did connect to existing OpenThread network. But now, all SDK3.0.2 devices...
I used the Bluetooth mesh distributor example from ncs2.9.1, and the Bluetooth mesh dfu can proceed normally. However, when I tried to pause and resume the dfu process, I...
Dear Nordic Support Team,
nPM2100, SHPHLD pin: we would like to connect a pushbutton to GND to wake the PMIC from ship mode. Additionally, we would like to read the pushbutton...
Hello, I am currently designing a custom board using the nRF9151 and I have a question regarding the SWD interface. My understanding is that the nRF9151 contains two main...
I've just spent about 4 hours trying to figure out why a particular build was failing (on nrf9151dk).
Examing the cryptic errors finally revealed that the TFM partition...
We're using the nPM1300 in our designs and we noticed that the charge portion does not appear to keep a battery charged when USB is connected for extended periods.
Our arrangement...
So far we have been using nRF5 SDK v17.1, but we ended up using nRF connect SDK v1.9.1.
However, this compiles too slowly.
I modified main.c and it seems to compile everything...
Hi,
I’m using NCS v3.1.0 and noticed that my application does not run unless I enable:
CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC=y
Without this configuration, the system fails...
HI TEAM,
I am using a custom board and measuring its overall current consumption using the NRF Power Profiler Kit 2 (PPK2) .
Setup details:
Power source: External...
Hi,
We are using the nrf9151 to get GNSS data/coordinates without using A-GNSS, we followed the information in the following page "https://docs.nordicsemi.com/bundle/ncs...
Hello Nordic Support Team,
We are currently developing an IoT product using the nRF9151. In our application, the device wakes up once per day, transmits a small amount of...
Hi, everyone
I am currently working on the development of Bluetooth and ANT+ on the nRF52832 chip. It communicates with my chip via UART, and now there are occasional disconnections...
