Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
The documentation in the nRF7002 Product Specification rev 1.0 says that the P2P mode (Peer-to-peer) is supported (section 6). However in this ticket: https://devzone...
I recently had a question about AES encryption on the nRF9160 and about how to store 32-byte encryption keys. The ticket was closed after I got the following answer: " we...
Hi,my board is nRF52840,and the demo is periodic_sync_conn within ncs2.7.0,
I want to establish periodic sync with the AP whose rssi is better，but i am failed。The ESL will...
Hello Nordic team,
I am working with the samples/bluetooth/shorter_conn_intervals sample on NCS v3.2.3 using two nRF54L15 DK boards.
I understand the difference between...
Hello, Recently I got an nRF9151-DK and I am following the Cellular IoT Fundamentals course. When it was time to connect the device to nRF Cloud (Lesson 1, Exercise 1), it...
Hi there,
I am developing a Matter light color temperature lamp product based on the NCS v3.1.1, and I need to store some custom user data in NVM (Non-Volatile Memory) within...
Hi engineers,
I posted a question at the link below, but it doesn’t seem to have received a response yet. If it’s convenient, could you please help answer the question?...
I'm debugging the function of switching between ESB and BLE. My general approach is as follows:
Initially, the BLE protocol stack is initialized, advertising starts...
Hello.
I'm looking for some advice debugging what I think is a race condition around bt_le_per_adv_sync_delete.
After calling bt_le_per_adv_sync_delete, we're sometimes...
Hi,
I am trying to use CoAP Block Transfer to transfer firmware images from server to nRF5340 custom board. We are using OpenThread library for CoAP.
The block transfer...
Hi,
For my university masters group project I need to connect my nRF5340 Audio DK to another board (Ambiq Apollo 510B). I will need to send audio from the mic to the Apollo...
Hi Nordic team, I’m working with nRF54H20DK on nRF Connect SDK v3.2.2 and using MCUboot as the bootloader. From the current documentation and samples, my understanding is...
Hello,
I'm trying the bootlader of SDK13.1, with SD S132_nrf52_4.0.2
I manage to send a ZIP file to the bootloader, but the application doesn't launch. I've tested with...
