Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hi,
I encountered a very strange issue. I need to control a device using GPIO. What I use is p0.22/p0.02/p0.03/p1.11/p0.31/p0.30. I modify the app.overlay file and check...
I'm running the SDK 17 radio test example on two custom board using nRF52833. My goal is to do a range measurement under ble_1Mbit mode.
My parameter as follows:
After...
Hi，
I am following the nRF Connect SDK Fundamentals course of Lesson 1 – nRF Connect SDK Introduction of Exercise 1 to install NCS development environment,when I executed...
When I tried to use PPK II to measure the alarm current of a smoke alarm product, I found that its test results were very different from those of the power analyzer. I didn...
Hi, I have a question regarding the nRF power management APIs. I'm trying to implement power management in my code, and I found that the pm_device_action_run() API can be...
Errata 36 for the nRF9161 (and the same problem exists on the nRF9151) disables the access port in SYSTEM ON IDLE, which is the default low power state for nRF9120 devices...
Hi,
My nrf9160-DK version is PCA10090, 1.1.3, 2023.31
I am trying to test the esim, but the firmware tells me no simcard found. After doublechecking the esim soldering...
Hello,
On T-Mobile's website [1] there are some documents relating to their certification requirements [2]. In their FAQ they state that they have minimum band requirements...
Hello, we are planning to evaluate several type of AoA algorithm, and we have ISP1907-AOA-DK kit from Insight-SiP Is there any guideline you know to get IQ data from each...
Hello, Im in the middle of a custom board bringup and I am attempting to get Bluetooth GATT server working. I have tested the bluetooth code using the nrf5340dk board files...
Hi,
I'm using nrf5340 audio dk board. I configured UART0 with the help of nrf connect fundamental course - Link and I started transmitting the data in UART. But after sometime...
Dear team,
I am trying to build my CPP project with Nordic Zephyr SDK. I am using following commands:
west build --build-dir nrf_build -b nrf52840dk_nrf52840 sample -DZEPHYR_TOOLCHAIN_VARIANT...
Hi guys,
starting to improve my throughput with an nrf52805 and S112, i know this version does not support DLE, but it's also the one with lower footprint, I will ask...
