Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hello, I cannot use UART1, and I don`t know the reason for that. I run the exercise: https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals/lessons/lesson-4-serial...
Hello,
When following Lesson 8: Exercise 2 – DFU over USB, adding external flash & custom keys, SDK v2.6.2, I encountered an issue with step 7.6. Upon issuing the command...
Hello support team,
I have two development kits: one nRF5340 DK and one nRF5340 AUDIO DK .
On the nRF5340 AUDIO DK , I have flashed the unicast server example. Now, I...
We are working on a project where 802154 radio runs on the NetCore. The NetCore firmware is based on the multiprotocol_rpmsg example by Nordic. Additionally, we have a custom...
SDK : NCS v2.8.0
SoC : nRF52840
HW : custom board
Hello,
I was trying to use settings subsystem, and I managed to make setting_write() and settings_read() work....
Hello, our entire code base is built around the Nordic SDK. We are considering designing a system that uses an nRF52840 as its controller but has no wireless functionality...
Setup: The nRF52840 DK is running the peripheral_hids_keyboard sample project. The device is connected to a macOS host, showing expected functionality.
Problem: When the...
Hi, We are using an nRF5340 and nRF Connect SDK v2.6.2. We have set CONFIG_BT_BUF_ACL_RX_SIZE to more than 251 and BT_CTLR_DATA_LENGTH_MAX to 251 in our prj.conf.
W hen...
my program works on the nrf52840 DK but does not work on the custom board using nrf52840-QFAA. We are using nrf sdk V2.8.0 running zephyr. Program is attached.
What to do...
Hello,
Version - nrf Connect SDK v2.7.0
The background to the system I am developing is described here and here
In short, I have an application containing a BLE Peripheral...
Hello everyone, I hope you have a good days. I'm developing an project for military standards. I'm using Nexys 4 DDR FPGA ev. board and VHDL language. My question is how can...
NCS 2.6.0, nrf52840
On our board we have attached a QSPI nor-flash as well as a SPI-based OLED display on the same pins.
I'm wondering if there has been any attempt...
In my application, I have implemented Serial Recovery. The interface used for the transfer is UART0 , which I also use in my application at a baud rate of 1M. When I enter...
I'm struggling to get a peripheral device to work with two simultaneous connections. I have attached my configuration (for the application) and my connect/disconnect callbacks...
