SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
We're currently developing a zephyr firmware on zephyr 4.2 and we got a custom board for our hardware powered by an nrf52840-ckaa-R
the first time I connected the board...
Hi all.
I've attached a single channel microphone onto my nRF9151 and I'd like to capture blocks of audio for processing. I've configured the device tree like this:
i2s...
Good evening.
I am working on a USB HID joystick. The USB documentation on nordic, while better than the woefully inadequate zephyr mainline docs, only covers the surface...
Hi,
I'm designing my device based on the Thingy53 layout and I have some questions:
The first is why, in the T53, the antenna division comes through U17 (PE4259) instead...
I recently began testing with the nPM1300EK and it seems like something is wrong with it. A number of different tasks don't seem to be working correctly:
Profiling a battery...
Greetings,
Using SDK v3.1.1 the SPI MISO signal appears to be actively driven by the nRF5280 for both my SPI1 and SPI2 configurations. In both cases there are no active...
Hi All,
I have to validate following use cases:
N reflector with nrf52833
1 initiator with nrf5340
The nrf5340 will be able to :
calculate distance from each...
Hi,
we are implementing MCUmgr SMP OTA over BLE (Zephyr + nRF54L15) with flutter, and I want to confirm that I’m generating the correct SMP upload packet format before streaming...
Hai, i try to MFRC522 rfid reader interface the nrf52833. 1. I try the read version from reader but it's only show the 0xFF 2.I try to read the card id . it is not work. I...
I'm unable to import/export mesh networks and then subsequently send mesh messages. I believe this problem has been mentioned before [ 1 ][2][3], but the solutions offered...
Hi,
We've had a mesh sensor network all working for a long time using SDK17.0.2 + Mesh SDK 4.1.0
The data is accessed by a mobile app through a mesh node acting as a proxy...
Hey
I am struggeling to build the smp_server sample for the nRF5340:
west build -p -b nrf5340dk/nrf5340/cpuapp/ns -- -DFILE_SUFFIX="nrf5340_bt"
fails with a linker error...
Hi Nordic Team,
I’m currently using two standard nRF5340 DKs (non-Audio DK) running the nrf5340_audio application.
We’ve successfully adapted I²S speaker output on unicast...
Hello, I am going to use nRF52833 to develop a remote controller based on Zigbee RF4CE specification.
From the nRF5 SDK for Thread and Zigbee, it looks like RF4CE should...
Hello,
Is there a way to change the LPCOMP reference level in Zephyr other than what is set in the devicetree overlay?
I'm happy to disable it, change it and re-enable...
