I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...
I'm trying to send simple packets using the radio peripheral.
In my test scenario I have the following conditions:
The HFXO is started and is running the whole time...
hi
the lengths of the this track is important?
if i decrease this length, how i can set antenna parameters?
another question: what is the R1 =0 ohm resistor and N...
I am using Fanstel evaluation board with BT805 attached.
I got an example project - ble to uart.
I was able to build the project with Segger V5.42 (any later verisons...
Dear all,
I tried this example regarding async SPI:
https://github.com/too1/ncs-spi-master-slave-example
I also wrote overlay for this example to work on nrf52840...
Hi, we have a custom nRF5340 based device. Has NISB and MCUBoot Enabled. It takes about 2.5 seconds to get into the application and BLE advertisement to start. Wanted to know...
Hello,
I´m trying to send a paket of databytes. For some reasons I need to send it byte by byte (that´s not changeable).
I have inited the uarte with a handler:
nrfx_uarte_init...
I am using the nPM PowerUp utility along with an nPM1300 development kit. The software provides options for configuring the soft-start current of the load switches. However...
Had an interresting issue that we have resolved, but we're trying to understand...
We had a timer (TIMER2) running and matching towards CC[3] every 500us. This match results...
Hi all,
I searched nRF54L PRELIMINARY DATASHEET v0.8 and found
9.1.1.2 DLPIDR: TINSTANCE field description reads " This value is set by the UICR.TINSTANCE register. "...
Hello Nordic Team,
I am writing on behalf of my company, where we are developing a cross-platform application using .NET MAUI . As part of our application, we need to implement...
Hi there
I'm trying to make the SPI work on nRF53 (My board is nRF7002 DK) refer the tutorial academy.nordicsemi.com/.../ but I had the issue about frequency of spi peripheral...
I'm using Bluetooth Mesh Sensor code, working on the nRF52833 DK. I want to add my own sensor, the ICM20948 IMU, to this function and send the sensor's readings to the Mesh...
Hi Support team,
My application was based on NCS v2.5.2, which has no driver for the charger bq24295, and I ported a driver from Linux and it worked well.
Now I want to...
