Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Hello,
My use case is the exact same use case as this forum post . I'd like to run BLE and Radio Test sample on the nRF5340. The device would be in 2 modes:
- BLE
-...
Hello,
I try to figure out, how to correctly setup MCUboot for an nrf5340, so that:
Application is updatable
BT Stack is updatable
Firmware Updates are encrypted...
I am trying to enable a watchdog and then stop it. i closely followed the datasheet way to do this. the problem is that the watchdog once enabled will always fire. i want...
I'm working on nRF5340 custom platform (NCS 2.6.1, Zephyr 3.5.99). I use MCUBoot immutable bootloader and external QSPI NOR Flash for slot-1 partition during DFU.
This is...
Hi Nordic Team,
I am working on the Matter Smoke/CO Alarm example with ICD (Intermittently Connected Device) support enabled.
My operational mode is working correctly...
I'm trying to replace HM-10 module with a RAYTAC MDBT42TV-DB-05 for a transparent UART (serial passthrough) application. I've configured all the parameters and GATT settings...
in fact , I have the while sdk directorys. in c:/ncs/v3.1.0 but,the nrf extension in vscode cannot recognize it. it always info me to install a sdk in welcome page. so, I...
I am using nRF52840, we have an issue which seems like a standard issue with nordic switching between regular battery and a coin cell backup.
I need to know the following...
Hi Support Team
Is the ifft the measured distance? I test the channel sounding sample in NCS v3.0.0 and find that the ifft distance error is relatively large. How to optimize...
My new PC could not find PPK in the power profile menu, even I installed different version nRF connect desktop or different Power Profile versions. I always could not find...
Hi:
I'll be using the Raytac Bluetooth Module in my project.
Imagine that the Bluetooth Module has a Bluetooth connection established with the smartphone (Android or...
Hi,
I am programming with ncs v2.9.0 based on nrf52833 chip
And base on peripheral_hid and central_hid
Testing that peripheral send data continuesly to central,and about...
Hello
I am attempting to perform BLE certification using a third-party module for the nrf52832.
Should I select the nRF Connect SDK QDID for all design items?
Or, should...
Hei,
I want to implement custom AT commands using a nrf9160 and ncs 2.8.0. The device should be able to process custom AT commands via UART console.
I followed this documentation...
