I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...
A new library/toolkit has been built that allows us to invoke the services of an nRF24L01 from a Java environment. Documentation and links to the Github project can be found...
Hi,
I am sending data from Android phone in every 200 ms to nRF8001. But sometimes I found there is a 50 ms or 100 ms delay. It looks like nRF8001 spending some time in...
Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
Hi,
I'm trying to connect multiple device on the same peripheral (nrf5340), but my peripheral does not restart advertising once a device is connected.
How to reproduce...
Now we don't add the external capacitance and want to change the internal capacitance . I have install the test tool and send the command to write the register,but it seems...
Hi!
I have nRF5340 Devkits and already have my own PCBs with nRF5340 chips onboard. I have a task where I need to evaluate how good will be BLE signal in different locations...
I know that I can memory-map external flash using XIP in the NRF52 and NRF53. However, with XIP, you can't write to the memory-mapped addresses (makes sense since you don...
Hi,
I have written a code for the motor driver and that is going to be flashed onto nRF5340. There are two communication buses that I am using in the code: UART and GPIO...
Hello Nordic,
we want to use the nrf9160 to measure some stuff and send data to a server while being battery powered. Therefore we need the lowest power consumption possible...
hi is there any existing frameworks for the nrf52 avoiding zephyr. (eg using common native cmsis / freertos / lwip stacks)?
ideally looking for free (non keil) based SD...
Hi,
Whenever I try to run the NUS example at 115200 baudrate there is an error. Either it triggers an assert or I receive corrupted data.
What should be the ideal baud...
Hi,
Trying to understand the NFC example code in the nRF52 SDK. Just wondering why the source code is not provided for the NFC. Why is this developned in the form of static...
I'm looking into the power consumption of our code, and have reached the point where it looks like our application isn't going into sleep mode properly, and is using several...
I'm developing battery powered Zigbee End Device on SDK 4.2.0. I need to be able to receive commands from Zigbee Coordinator so I'm using SYSTEM ON sleep mode.
Right now...
Hi,
I'm using nRF9160 SLM application SDK 1.9.1
We are using the GPS in 4 operation modes and in between we sent nRF to sleep, it seems when we sent it to sleep all...
Hello,
I do not see a SWO (Single Wire Output) pin on this package. The regular size package has this function on P0.18 but not on the WLCSP package.
Please advise.
...
Hi,
I have several devices with the RIGADO BMDWare on them but whose hardware is inaccessible. I want to initialize these nRF52832 chips with out nRF Bootloader, Softdevice...
